Table of Contents
Advertisement
Quick Links
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
WARNINGS
• Hot! Do not touch! The glass and
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appli-
ance. Severe burns may result.
• Carefully supervise children in the
same room as appliance.
Intertek
Listed to standards:
ULC-S610 & UL-127
ASTM 2558
Report No. 192-5237
PISOLANA REV. 2 06/2010
INSTALLATION AND
OPERATION INSTRUCTIONS
Solana™
EPA Low-Mass Wood-burning Fireplace Phase 2 Qualified
43" Wood-Burning Fireplaces
P/N 506023-07 REV. B 06/2010
MODELS
SOLANA-BK
SOLANA-BN
This installation manual will enable you to obtain a safe, efficient
and dependable installation of your fireplace system. Please read
and understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any cir-
cumstances. Any modification or alteration of the fireplace system,
including but not limited to the fireplace, chimney components and
accessories, may void the warranty, listings and approvals of this system
and could result in an unsafe and potentially dangerous installation.
Lennox Hearth Products wood-burning fireplaces are designed for use
as a supplemental heater. They are not intended for continuous use
as a primary heat source.
• The fireplace cannot be operated without doors
or firescreens. Consult your dealer to select the
correct replacement door(s) or firescreen(s).
• Important! To assure proper alignment of glass
doors: Install this fireplace in a square and
plumb condition, using shims as necessary at
sides and/or bottom.
• Install the fireplace only as described in these
instructions.
WARNINGS
TM
Advertisement
Table of Contents
Related Manuals for Lennox SOLANA-BK
Summary of Contents for Lennox SOLANA-BK
-
Page 1: Operation Instructions
Lennox Hearth Products wood-burning fireplaces are designed for use as a supplemental heater. They are not intended for continuous use as a primary heat source. -
Page 2: Safety Rules
IMPORTANT! GENERAL SAFETY CAUTION WARNING PRECAUTIONS. READ AND UNDERSTAND THESE SAFETY Use care when selecting window To avoid the risk of damaging RULES BEFORE YOUR FIRST FIRE. treatments for windows located fireplace materials and increas- near the fireplace. Avoid using ing the risk of fire, do not use the WARNING combustible flowing window... -
Page 3: Table Of Contents
- VRUW Blower motor speed control benefit and enjoyment available from your new fireplace. - Forced Air Heating Kit Thank you for selecting a Lennox Hearth Products fireplace as the answer to your home If installed, this appliance no longer qualifies supplemental heating needs. -
Page 4: Operating The Fireplace
OPERATING THE FIREPLACE Do not burn scrap or garbage, treated wood or Building A Fire wood such as driftwood from the ocean which Fuel has been exposed to salt or other chemicals. (starting and maintaining a fire) Salt or chemicals can corrode the firebox and To start a fire, place several crumpled up balls of USE SOLID NATURAL WOOD FUEL ONLY. -
Page 5: Outside Air Register
CLOSING THE DOORS D. Wet wood HOW TO USE THE OUTSIDE AIR REGISTER Wet or tarred wood will smoulder and smoke (FIREPLACE) As soon as a layer of embers covers the surface instead of burning properly. Your dealer can The outside air register is located on the up- under the log retainer, it is possible to close help you determine if you have properly per left part of the top louver. -
Page 6: Maintaining Your Fireplace
MAINTAINING YOUR FIREPLACE Caution: It is necessary to remove the baffle from the top of the firebox before cleaning the chimney. Creosote - Formation and Need for Removal When wood is burned slowly, it produces tar Dealing With a Chimney Fire and other organic vapors, which combine with expelled moisture to form creosote. -
Page 7: Refractory Replacement
(see fastening screws in Figure 5). If a minor angular adjustment is needed, you may loosen • Use only a Lennox Hearth Products glass doors, specifically designed only two (2) of the three (3) screws using the for the Solana fireplace. -
Page 8: Glass Care - Replacement
This replacement part is available from your THE UNIT WITH CRACKED OR BROKEN GLASS. rectly on the floor or on a raised base (for Lennox Hearth Products dealer in the following To remove the glass, unscrew the frame fasten- proper guidelines, refer to “Hearth Extension... -
Page 9: Preinstallation
Wall Square and safe installation and reliable operation. Fireplace Failure to use Lennox Hearth Products parts If gas pipe is used: or conduct variations in techniques and Pipe wrench construction materials described in this... -
Page 10: Mantel
Mantel A wood mantel, if installed, must be at least 48" (1.2 m) above the base of the fireplace (see WARNING: THE HEARTH EXTEN- Fireplace Figure 8B). There is no restriction regarding SION IS TO BE INSTALLED ONLY the length or the width of the mantel. AS ILLUSTRATED. -
Page 11: Fireplace And Framing Dimensions
Do not fill the space 23-11/32” above the fireplace with any mate- rial (except the wood framing) (593mm) Notes Due to Lennox Hearth Products ongoing commitment to quality, all specifications, ratings and dimensions are subject to 2" X 3" change without notice. MIN. -
Page 12: Insulated Chase Construction
Insulated Chase Construction Flashing Roof support Non-combustible Insulate Joists chase top Same As Ceiling Ceiling / floor separation Attic firestop Draft Stops Firestop NOTE: It is recommend- • Must have the same fires rating as CTDT adjacent ceiling. ed that the chase walls Termination •... -
Page 13: Outside Air Assembly
Outside Air Assembly (Fireplace and AC Chimney) The outside air assembly is mandatory for the fireplace and the AC chimney. During operation, the fireplace requires air for combustion and draws air out of the house. It may starve other fuel burning appliances such as gas or oil furnaces. -
Page 14: Uzy5 Blower Kit
INSTALLATION OF THE BLOWER KIT MODEL UZY5 CENTRAL FORCED AIR KIT If this kit is installed, this appliance no longer qualifies for EPA Low NOTE: This blower kit can easily be installed when the fireplace has a Mass Wood-burning Fireplace Program. pre-installed junction box. -
Page 15: Chimney System
CHIMNEY SYSTEM GENERAL INFORMATION The Solana™ fireplace is listed only with Security Chimneys™ Interna- two (2) feet Min. tional Ltd. chimney systems, models ASHT+ 8", S-2100+ 8", or AC 8". three (3) feet Min. Do not connect the fireplace to a masonry chimney, chimney liner, or ten (10) feet other brand of factory-built chimney. -
Page 16: Chimney Installation Instructions
CHIMNEY INSTALLATION INSTRUCTIONS 1. Cut and frame the holes in the ceiling, Attic Radiant Firestop floor and roof where the chimney will pass (see Figure 19). Use a plumb-bob to line AC RSA up the center of the holes. The hole sizes are indicated in Table 3 for the floor and ceiling holes and in Table 4 (Page 17) for the roof holes. -
Page 17: Offset Chimney Installation
After reaching the location requiring the elbow, proceed as follows: Air Cooled Chimney Chimney ASHT+/HT6103+/S2100+/HT6000+ Chim- neys Collar Spacer (built Install the first elbow. Turn it in into flashing) the required direction. Fasten it to the chimney with the three (3) 1/2" (12mm) metal screws provided. - Page 18 Offset Dimensions Total Height Horizontal Offset Chimney Elbow Offset & One Length Between Elbows Two Lengths Between Elbows 8” Height 8” 12” 18” 24” 36” 48" 8” & 48” 12” & 48” 18” & 48” 24” & 48” 36” & 48” 48”...
-
Page 19: Angled Wall Radiation Shield
ANGLED WALL RADIATION SHIELD (RSM+, RSMI30, RSMI45) OFFSET CHIMNEY INSTALLATION When traversing a combustible wall with the chimney at a 30° or 45° Chimney AC angle, an angled firestop and/or wall radiation shield must be installed. Only one is required (Figure 27). Table 6 gives recommended hole size for installing a wall radiation shield. -
Page 20: Universal Roof Support
UNIVERSAL ROOF SUPPORT INSTALLATION This support has three possible uses: 18” (460 mm) 18” (460 mm) For ASHT+ and S-2100+ chimneys, it must be used on a roof to support the chimney. It may be used on a floor, ceiling or roof above an offset to support the chimney above the offset. -
Page 21: Installation Accessories
OPTIONAL INSTALLATION ACCESSORIES - SOLANA™ Installation Accessories Description Cat./ Part No. Installation Accessories Forced Air Heating Kit Description Cat./ Part No. Starter Kit includes: blower (BISZY), flex adaptor and BISFWK-1 Outside Air Kit (Required - Included with Fireplace) two clamps (BISAF), blower variable speed control (VRUW), Thermo-disc (VTU), blower flex adaptor Outside Air Coupler to connect outside air UZI to UZIDF... -
Page 22: Chimney Components Lists
COMPONENTS LIST - SOLANA™ Secure Temp™ ASHT+ High Temp. Insulated Stainless Steel Chimney AC Chimney 8" Diameter, Listed to CAN / UCL-S604 and UL-103HT at 1200° F (Air Cooled - 8" I.D., 13" O.D.) Description Cat./ Part No. Description Cat./ Part No. Lengths and Misc. -
Page 23: Specifications
CLEARANCE TO COMBUSTIBLES Fireplace Cat. No. Model Description The following clearances meet the minimum requirements for a safe H7703 SOLANA-BK Solana (w/Black Doors) installation; H7704 SOLANA-BN Solana (w/Brushed Nickel Doors) Side wall: 18” (457 mm) Ceiling: 7 feet (2135 mm) measured from the base of the fireplace... -
Page 24: Replacement Parts
P/N PR-ISO2938 , P/N PR-ISO2939 and P/N PR-ISO2750. Brushed Nickel Plated Door (Right) H7709 Contact an Authorized Lennox Hearth Products dealer to obtain any of Wooden Handle PR-SAC83 these parts. Never use substitute materials not approved by Lennox... - Page 25 REPLACEMENT PARTS - SOLANA™ NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
-
Page 26: Product Reference Information
Your Dealer's Name _________________________________________________ Your Dealer's Phone Number __________________________________________ Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.