Related Manuals for MULTIQUIP Mayco C30HDG
Summary of Contents for MULTIQUIP Mayco C30HDG
- Page 1 INSTALLATION/OPERATION MANUAL MIRATRON WIRELESS REMOTE CONTROL RADIO MAYCO MODEL C30HDG Revision #0 (08/19/09) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Warranty ......3 Overview ......4 Specifi cations ....5 Care And Handling ..... 6 Receiver Installation ..7-8 Cable Installation ....9 Wiring Diagram....10 Transmitter/Receiver ..11-12 Troubleshooting ....13 System Wiring Diagram ..14 PAGE 2 —... -
Page 3: Warranty
WARRANTY LIMITED ONE YEAR WARRANTY Miratron Incorporated, hearafter referred to as Miratron, is providing this warranty in lieu of all other express or implied warranties, including any warranty of merchantability or fi tness for a particular purpose. This warranty is buyer’s exclusive remedy for all claims against Miratron. Miratron shall not be liable for any consequential or incidental damages. -
Page 4: Overview
OVERVIEW ALWAYS read manual before attempting to operate the equipment. Failure not to read manual could cause severe equipment damage and or damage to the receiver and transmitter. Make sure work area is safe to operate radio control receiver and transmitter. -
Page 5: Specifi Cations
SPECIFICATIONS Table 1. Specifi cations Miratron Model Number: RX4 Radio Control Receiver CMD16-0135 ~ (MQ P/N EM98215) General: Power Requirements 12-24VDC, 500mA max Radio: Frequency Standard 902-928 MHz, FHSS, ISM Band Frequecy Control Direct FM FCC ID OUR9XCITE (Standard) Receiver Sensitivity -106 dBM CMD16-0135 ~ (MQ P/N EM98215) Transmitter:... -
Page 6: Care And Handling
CARE AND HANDLING Transmitter: Clean transmitter gently with a damp cloth. DO NOT immerse transmitter in water, or spray with hose. DO NOT store outside. DO NOT drop transmitter or otherwise subject transmitter to physical shock. DO NOT expose transmitter to extreme temperatures. -
Page 7: Receiver Installation
Disconnect the negative terminal of the battery cable from the battery. Ant enna Mounting Drill a 3/4” hole into the hood on the C30HDG as shown in Figure 1. After hole has been drilled, deburr hole opening. Tilt the engine hood slightly forward to gain access to the antenna hole opening. -
Page 8: Receiver Installation
RECEIVER INSTALLATION Radio Control Receiver Mounting Drill two 1/4” holes into the control box support panel on the C30HDG as shown in Figure 1. After both holes have been drilled, deburr each hole opening. Using a 1/4-20 x 1-1/4 bolt (2), 1/4 lock washer (2), 1/4 fl at washer (2) and 1/4 nut (2), mount the radio control receiver onto the control box support panel as shown in Figure 1. -
Page 9: Cable Installation
CABLE INSTALLATION Control Box Removal Using a 7/16 socket remove the mounting bolts (3) that secure the control box to the support bracket. Once the bolts have been removed, fl ip the panel downward to gain access to the connection points. Data Cable Connections Wire data cable into control box as shown in Figure 2. -
Page 10: Wiring Diagram
WIRING DIAGRAM RED OR PINK 12-PIN DATA CABLE I V E SPLICE ENGINE OIL SENSOR EMERGENCY STOP PIN 4 (WHITE) HOUR METER 7-WIRES FRAME GROUND BLACK BATT + (RED) TERMINAL DECREASE (WHITE) RING INCREASE (WHITE) CHECK HOOD ENGINE OPEN REMOTE (WHITE) PIN 9 (WHITE) WHITE BLACK... -
Page 11: Transmitter/Receiver
TRANSMITTER/RECEIVER The defi nitions below describe the controls and functions of the Miratron Transmitter and Radio Control Receiver. Transmitter Power On Switch — Place this switch in the ON position to turn on the transmitter. Be sure to place this switch in the OFF position when the system is not in use. - Page 12 TRANSMITTER/RECEIVER Functional Test Perform the functional test procedure below to test the remote control radio system.. Start the engine as outlined on the operator’s manual. Place the transmitter power ON/OFF switch in the ON position. Place the pumping control switch on the control box in the REMOTE ON position.
-
Page 13: Troubleshooting
TROUBLESHOOTING Table 2. Troubleshooting Symptom Possible Problem Solution Transmitter does not LED status indicator not Turn transmitter power function at all fl ashing. switch ON. Weak dead battery, replace batteries. Check orientation of batteries. Make sure transmitter has LED indicator not lit when be matched (paired) to power ON/OFF switch is receiver. -
Page 14: System Wiring Diagram
SYSTEM WIRING DIAGRAM Figure 4. System Wiring Diagram PAGE 14 — INSTALLATION OPERATION MANUAL — REV. #0 (08/19/09) - Page 15 NOTE PAGE INSTALLATION/OPERATION MANUAL — REV. #0 (08/19/09) — PAGE 15...
- Page 16 © COPYRIGHT 2009, MULTIQUIP INC. Multiquip Inc, the MQ logo and the Mayco logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.