Related Manuals for ABC Office 24501
Summary of Contents for ABC Office 24501
-
Page 1: Users Guide
Ketec, Inc Shoplifting Protection USERS GUIDE SP-1 KT7060 abcoffice www.abcoffice.com 1-800-658-8788 24501... -
Page 2: Table Of Contents
SP-1 USERS GUIDE INDEX Parts List …………………………….1 Assembly Instructions……………… 2 Positioning the System ……………. 3 Tagging Guidelines …………………4 Removing Hard Tag……………….. 7 Detection Area ……………………... 9 Alarm Handling …………………….. 10 Troubleshooting ……………………. 11 Warranty…………………………….. Back Cover abcoffice www.abcoffice.com 1-800-658-8788... -
Page 3: Parts List
Remove all contents from packaging. Compare products with the example. If you are missing any parts please contact your supplier immediately. The carton should contain: SP-1 ANTENNA WITH WIRE abcoffice www.abcoffice.com PARTS LIST CAP NUTS AND WASHERS POWER SUPPLY WITH 10’ OF 5’... -
Page 4: Assembly Instructions
ASSEMBLY INSTRUCTIONS 1. Locate the baseplate, cap nuts and washers. 2. Place the antenna on top of the baseplate, aligning the holes in the antenna base with the studs on the baseplate. Make sure that the power supply wire is in the channels of the antenna base and is not crushed between the antenna base and the baseplate. -
Page 5: Positioning The System
POSITIONING THE SYSTEM 6. Position the system a minimum of 18” (Inches) from the doorframe and on the side closest to the door handle. 7. Cut the rubber molding to the length that will allow it to cover the wire from the wall to the system. -
Page 6: Tagging Guidelines
TAGGING GUIDELINES 1. The tag should be visible to the customer. 2. Tag uniformly, it speeds up removal. 3. Tag near a price label. It assists in the removal. 4. Place the tag as high as possible when tagging silks & light or stretchy fabrics. - Page 7 TAGGING GUIDELINES Dresses Pants Bikini Bathing Suit One Piece Bathing Suit abcoffice www.abcoffice.com 1-800-658-8788...
- Page 8 TAGGING GUIDELINES Shoes Tennis Shoes Belts Purses abcoffice www.abcoffice.com 1-800-658-8788...
-
Page 9: Removing Hard Tag
REMOVING HARD TAG 1. Place the hard tag into the detacher with the pin facing 2. Remove the pin by holding the hard tag to the detacher and pulling straight up on the pin or garment. 3. Remove the pin and hard tag from the detacher and store for future use. - Page 10 REMOVING HARD TAG It is possible for the locking mechanism to become jammed when the pin is pulled extremely hard. It is possible to un-jam the pin so that you will be able to remove it when needed. The first step is to place the hard tag into the detacher then press on the head of the pin.
-
Page 11: Detection Area
The SP-1 system will detect hard tags within 4 feet to each side and 3 feet in front of and back of the antenna. We recommend that you keep all merchandise with hard tags a minimum of 4-1/2 feet from the sides of the system and 3 feet from the front of and back of the system. -
Page 12: Alarm Handling
There are three reasons for the system to alarm: 1. The REAL alarm: The occurrence of a shoplifting attempt. 2. The ACCIDENTAL alarm: a) Personnel neglected to remove a tag at the point of sale. b) An electronic security access card has been carried into the store by a customer, or c) A previously purchased product, with an active tag, from another store using a similar system. -
Page 13: Troubleshooting
If a problem develops with the SP-1 system it is usually caused by common occurrences. The following is a basic troubleshooting guide to be used prior to contacting your supplier if the need arises. DO NOT MAKE ANY INTERNAL ADJUSTMENTS TO THE SYSTEM PRIOR TO CONTACTING YOUR SUPPLIER. NO DETECTION 1.
Need help?
Do you have a question about the 24501 and is the answer not in the manual?
Questions and answers