Fellowes POWERSHRED 53C Quick Manual page 3

BASIC SHREDDING OPERATION
Continuous operation:
Up to 3 minute maximum
NOTE: Shredder runs briefly after each
pass to clear entry. Continuous operation
beyond 3 minutes will trigger a 30-minute
cool down period.
TROUBLESHOOTING
PAPER JAM
1 2
Set to Reverse (R) Alternate slowly back and forth
for 2-3 seconds
PRODUCT MAINTENANCE
OILING SHREDDER
All cross-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding, and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
1 2
Set to Off (O) * Apply oil
across entry
* Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
LIMITED PRODUCT WARRANTY
Limited Warranty: Fellowes, Inc. ("Fellowes") warrants the parts of the machine to be free of
defects in material and workmanship and provides service and support for 2 years from the date
of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to
be free from defects in material and workmanship for 5 years from the date of purchase by the
original consumer. If any part is found to be defective during the warranty period, your sole and
exclusive remedy will be repair or replacement, at Fellowes' option and expense, of the defective
part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product
usage standards, shredder operation using an improper power supply (other than listed on
label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any
Australia Residents Only:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The benefits under Fellowes' Warranty are in addition to other rights and remedies under a law in relation to the shredder.
PAPER OR CD/CARD
1 2
1
Plug in and put
Set to Auto-On (I)
disconnect power
switch in ON (I) position
4
3
Set to Off (O)
and unplug
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions, the
sensors may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry)
TO CLEAN THE SENSORS
3
1
Set to Reverse (R) Turn off and unplug
shredder
2-3 seconds
15
3 4
or
Feed paper straight Feed into card/CD entry
into paper entry and release
and release
6
5
Gently pull uncut Set to Auto-On
paper from paper
(I) and resume
entry. Plug in.
shredding
2
Locate Auto-start
infrared sensor
additional costs incurred by Fellowes to provide parts or services outside of the country where the
shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable
for any consequential or incidental damages attributable to this product. This warranty gives you
specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide,
except where different limitations, restrictions, or conditions may be required by local law. For
more details or to obtain service under this warranty, please contact us or your dealer.
5
When finished shredding
set to OFF (O)
Shredder doesn't start:
Make sure head is on basket correctly
Wait 30 minutes for motor to cool down
Remove and empty basket
.
3
4
Dip cotton swab in Using cotton swab, wipe
rubbing alcohol away any contamination
from the paper sensors