Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for American Dryer Corp. Microprocessor 8.4 Rev 2.2
- Page 1 Phase 8.3 and 8.4 Rev 2.2 Microprocessor User’s Manual American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447 e-mail: techsupport@amdry.com www.amdry.com ADC Part No. 113604-4...
-
Page 2: Table Of Contents
Retain This Manual In A Safe Place For Future Reference Please read this manual carefully to thoroughly familiarize yourself with the Phase 8 microprocessor controller (computer) system features, operational instructions, and programming characteristics. This manual contains important information on how to employ all the features of your new dryer in the safest and most economical way. -
Page 3: General User Information Coin/Debit Models "Coin Dry Mode
Important Read all instructions before operating! General User Information Coin/Debit Models “Coin Dry Mode” ___ Cold Start (Initial/First Use) Appliance is programmed at the factory as follows: Dryer 10 minute dry time/quarter (coin 1) $.25 dry price Warm Start (After Power Failure) A few seconds after power is restored, if a cycle was in progress at the time of the power failure, the display will prompt “Select Cycle to Restart”. -
Page 4: Introduction To Programming
Introduction to Programming _________ The keypad along with the digital display are used to setup the dryer controls. Entering and Exiting Service Mode Entering Coin/Debit Models Use security key to activate programming mode. Non-Coin (OPL) Models To enter the Program Mode you must hold the STOP key and the UP ARROW key down. -
Page 5: Factory Settings
Quick Reference Programming Menu for Coin/Debit/Free Models _________________ Machine Info Program Setup KEY FUNCTIONS Scroll down/decrease value HIGH Scroll up/increase value MEDIUM Accept selection PAUSE / STOP Back out of a location Diagnostic Mode Machine Setup Factory Settings 113604 - 4 Coin Vault Hours Serial #... -
Page 6: Quick Reference Programming Menu For Non-Coin (Opl) Models
Quick Reference Programming Menu for Non-Coin (OPL) Models _________________ Machine Info Program Setup KEY FUNCTIONS DOWN ARROW Scroll down/decrease value UP ARROW Scroll up/increase value ENTER Accept selection PAUSE / STOP Back out of a location Diagnostic Mode Machine Setup Factory Settings Hours Serial #... -
Page 7: Coin Programming Example Changing "Time For Amount To Start
Coin Programming Example Changing “Time for Amount to Start” Below is a flowchart explaining how to change the time allotted for the start price on coin machines for all temperatures. This is meant to be an example as there are many options and ways to program this controller. -
Page 8: Non-Coin (Opl) Factory Preset Programs/Parameters
Non-Coin (OPL) Factory Preset Programs/Parameters _____________________________ The following are the default cycle descriptions: Cycle Type Cycle Name Auto / Manual DENIM AUTO HEAVY AUTO TOWELS AUTO HAND TOWELS AUTO WHITES AUTO COLORS AUTO SHEETS AUTO COTTONS AUTO DELICATES AUTO EXTRA DELICATE AUTO WRINKLE REMOVAL MANUAL... -
Page 9: Programming Selections
Programming Selections ______________ MAIN MENU When PROGRAM Mode is first entered, the control will enter the PROGRAM Mode main menu. This main menu will serve as the gateway to all of the PROGRAM Mode features. The features include MACHINE INFO, PROGRAM SETUP, DIAGNOSTIC MODE, MACHINE SETUP, and FACTORY SETTINGS. - Page 10 2: MACHINE SETTINGS 1: LINT CLEAN FREQ. – adjusts time between prompts to clean lint. (adjustable between 0 - 3 hours, 0 being off) 2: AXIAL MAX TEMP – adjusts axial probes set maximum temperature (adjustable between 100° - 180° F / 38° - 82° C) 3: BURNER SETUP One burner / Two burner (option not available for stack units)
- Page 11 3: DIAGNOSTIC MODE 1: FAULT RECORDING 1: UPPER DRYER FAULTS* When a fault is recorded on the top pocket, it can be viewed in this location. If no fault(s) have been recorded, then “NO UPPER FAULTS” will be displayed. 1: (Description of fault) 2: (Description of fault) 3: (Description of fault) 4: (Description of fault)
-
Page 12: Code Description
When a cycle is running, the control will display DIAGNOSTIC MODE at the top of the display. If a fault occurs during Diagnostic Mode, the control will enter into a fault cool down and the occurring fault will be displayed. The fault can be cleared by reentering the diagnostic cycle. -
Page 13: Faults
Faults __________________________________ Exhaust Probe An exhaust probe fault occurs when the control detects that the exhaust temperature transducer is reading a temperature that is out of the probe’s normal operating temperature range for more than 3-seconds. There is an automatic fault clearing feature for this fault. - Page 14 ADC Part No. 113604 4 - 07/25/08 - 200...
Need help?
Do you have a question about the Microprocessor 8.4 Rev 2.2 and is the answer not in the manual?
Questions and answers