Related Manuals for Panasonic PT-TX301R
Summary of Contents for Panasonic PT-TX301R
- Page 1 PT-TX301R P ro d u c t N u m b e r : ™ Short-Throw DLP Projector P ro d u c t N a m e : As of September 2013. Specifications and appearance are subject to change without notice.
- Page 2 PT-TX301R Short-Throw DLP ™ Projector Specifications Main unit Power supply 100−240 V AC, 50/60 Hz Power consumption 301 W (0.5 W when set to , 6.0 W when STANDBY MODE set to STANDBY MODE NORMAL. DLP™ chip Panel size 14.0 mm (0.55 inches) diagonal (4:3 aspect ratio) Display method DLP™...
- Page 3 PT-TX301R Short-Throw DLP ™ Projector Built-in speaker 7 × 4 cm Oval x1 output power 8 W (Monaural) Power cord length 3.0 m (9 ft 10 in) Cabinet materials Molded plastic (PC) Dimensions (W × H × D) 288 x 106*...
- Page 4 PT-TX301R Short-Throw DLP ™ Projector Dimensions 288(11-11/32) 70.8(2-25/32) 118(4-21/32) unit : mm (inch) unit : mm (inch) NOTE: This illustration is not drawn to scale. NOTE: This illustration is not drawn to scale. Terminals HDMI input Monitor output MONITOR OUT...
-
Page 5: Standard Setting-Up Position
PT-TX301R Short-Throw DLP ™ Projector Standard setting-up position unit : mm (inch) ø38 (1-1/2) Upper edge of projected image (5-1/32) (4-21/32) Screen Lower edge of projected image (8-29/32) (7-7/8) NOTE: Screen Illustrations show the projector installed using optional ceiling mount bracket ET-PKV100H and attachment ET-PKL300B. - Page 6 PT-TX301R Short-Throw DLP ™ Projector Projection distance for 4:3 aspect ratio screen unit: meters (feet) Projection size Height from the edge of screen Projection distance [L] to center of lens [ H ] [diagonal] 1.02 m 40˝ (1.7) -0.09 (-0.30) 1.27 m...
- Page 7 PT-TX301R Short-Throw DLP ™ Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Display mode Display Scanning frequency Dot clock Format resolution frequency (dots) (kHz) (Hz) (MHz) NTSC/NTSC4.43/PAL-M/PAL60 59.9 –...
- Page 8 PT-TX301R Short-Throw DLP ™ Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below.
- Page 9 PT-TX301R Short-Throw DLP ™ Projector Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. C2 C3 P1 P2 ... Pn...
-
Page 10: Status Request Commands
PT-TX301R Short-Throw DLP ™ Projector Status request commands Command : Parameter Function Callback Description Main power status Standby Lamp on status Standby Lamp on control in progress Lamp on Lamp off control in progress AV mute function status Input signal status... - Page 11 PT-TX301R Short-Throw DLP ™ Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. Never place objects on top of the projector while it is operating.