Subscribe to Our Youtube Channel
Related Manuals for Goodmans X-Pro GLCD15M2
Summary of Contents for Goodmans X-Pro GLCD15M2
-
Page 1: Instruction Manual
GLCD15M2/GLCD17M 15” / 17” MONITOR INSTRUCTION MANUAL Goodmans Product Information Helpline: 0870 873 0080... -
Page 2: Table Of Contents
Contents Introduction ..........................3 Features ............................3 For safe use of this product ......................4 Installation ........................... 5 Unpacking the Display ........................5 Locations and Functions of Controls .................... 5 Making the Connections ....................... 6 Using The Display ........................8 Turning the Display On and Off .................... -
Page 3: Introduction
Introduction This latest LCD monitor has a 15-inch/17-inch active matrix TFT (thin film transistor) liquid crystal display module. It can be used with set top boxes. DVD players, VCR’s and also windows based PC’s. Features Important features include: Automatic configuration to the PC video settings with maximum XGA (15” 1024*768) / SXGA (17”... -
Page 4: For Safe Use Of This Product
For Safe use of this product For safe and the protection of the monitor, please follow these precautions: Warning To completely disconnect power from the display, you must remove the power cord from the wall outlet and then remove the power cable from the disp lay. Use only the factory-supplied power adaptor shipped with the monitor. -
Page 5: Installation
Installation Please follow the instructions in this chapter to install the LCD Monitor. Note: Before connecting the display, first read through the instructions in this chapter and the safety precautions on the previous page. Unpacking the Display When unpacking the display, make sure that the following items are present: The LCD monitor AC power adapter with attached DC power cable. -
Page 6: Making The Connections
The power button is located on the lower right of the panel. The functions of the five control buttons, which are located on the front panel of the display, are described as below: Button Function Description (1) PC or PC+AV: Launches the OSD menu. Menu/Exit (2) OSD exit. - Page 7 When using with a PC: 4. Plug the analogue video signal cable into the Analogue Video Input port on the back of the display (“VGA IN“ as shown above). 5. Connect the other end of the video cable into computer’s video port. (Please check computer’s documentation if you’re not sure where the port is located.) Note: For best display performance, it is strongly recommended that Auto Setup be used to...
-
Page 8: Using The Display
Using The Display Turning the Display On and Off Use the power button located at the lower right side of the front panel to turn the display on and off. When the display is on, the LED near the Power button is illuminated. The indicator will illuminate green when the display is active and amber when the display is in reduced power mode. -
Page 9: Setting The Video Mode (Pc Only)
Setting the Video Mode (PC only) Since the inherent format of this display is 1024 pixels by 768 lines for 15” monitor and 1280 pixels by 1024 lines for 17” monitor, the display will perform best when a PC is set to a screen resolution of 1024 x 768 for 15”... -
Page 10: Caring For And Cleaning The Display
Caring for and Cleaning the Display To maximize screen life and prevent damage to the LCD panel, we recommend to: Use the display power management system (if available on the PC). If a power management system is not used, turn off the display when it won’t be used for an extended period. -
Page 11: Adjusting The Display
Adjusting The Display Functions of Control Buttons See “ Locations and Functions of Controls “ on page 5. Displaying the OSD “Main Menu” (Only for PC mode) To display the OSD “ Main Menu “, press the Menu/Exit button. -
Page 12: Selecting Items In The Osd Menu
The following table briefly describes each of the items on the OSD “ Main Menu “. (Colour Menu, Picture Menu) Colour Menu: Item Description Contrast Adjust the level of difference between light and dark areas of the image. Brightness Controls the brightness of the display. Gamma Correct Select 0 ~ 3 to meet the correct Gamma on different LCD panel Colour Temp. -
Page 13: Making Adjustments Via The Osd Menu
Making Adjustments Via the OSD Menu Enter Colour Menu: Adjusting Contrast Press the Menu/Exit button to show the OSD Colour menu. The contrast icon will be highlighted (White) Press the Mode/Enter button to select this option Using the Left and Right control buttons increase or decrease the Contrast level as required between the limits of “... -
Page 14: Adjusting Gamma Correct
Adjusting Gamma Correct Press the Menu/Exit button to show the OSD Colour menu. The Contrast icon will be highlighted (white). Press the Right control button, until the Gamma Correct icon changes to white to indicate it is the active function. Press the Mode/Enter button to select this option. -
Page 15: Adjusting Colour Adjust
Colour Adjustment Press the Menu/Exit button to show the OSD Colour menu. The Contrast icon will be highlighted (white). Press the Right control button, until the Colour Adjust icon changes to white to indicate it is the active function. Press the Mode/Enter button to select this option. Use the Left and Right control buttons to adjust the Red, Green, Blue level then press Mode/Enter button again. -
Page 16: Picture Menu
Enter Picture Menu: In Colour Menu, use the Right control button to highlight “ Picture Menu“. Press the Mode/Enter button to show the Picture Menu. The H. Position icon will be highlighted (white). Use the Left and Right control buttons select the required feature from the menu. To adjust the image position, In H. -
Page 17: Displaying The Osd "Set Up Menu" (For Av Mode, S-Video Mode)
Monitor connected to a Set top box, DVD player or VCR With the monitor connected to a set top box, DVD player or VCR ONLY, adjustments can be made via the set up menu as below. Press Mode / Enter button to select AV or S-Video mode. To display the “Set up Menu”, press the Menu/Exit button. -
Page 18: Selecting Items In Osd "Set Up Menu
Selecting Items in the OSD “ Set up Menu “ To select items in the “ Set up Menu “, use the Mode/Enter button on the front panel of the monitor. To select items in the submenus, use three (Mode/Enter, , ) control buttons. To select a specific submenu, use the Mode/Enter button to locate the required option. -
Page 19: Troubleshooting
Troubleshooting This chapter contains information about how to troubleshoot problems. If you have tried all of the items listed below, please contact a qualified service personnel. A. My display doesn’t work, even though the computer appears to work. 1. Make sure the power cable is securely plugged into the display. 2. -
Page 20: Technical Information
Technical Information This chapter contains technical information about the LCD Monitor. Display Information GLCD15M2 GLCD17M 15-in (38.0 cm), active matrix TFT, anti-glare 17-in (43 cm), active matrix TFT, anti-glare LCD Module coating, 0.297 mm pixel pitch coating, 0.264 mm pixel pitch Display Size 304.1 mm x 228.1mm... -
Page 21: Video Modes
Video Modes Your LCD monitor supports the following industry-standard combinations of screen resolution and refresh rates. Other combinations are possible, but may require adjustments to the image. For optimum performance, set your PC to a screen resolution of 1024 x 768 at a 75Hz refresh rate for 15”... -
Page 22: Unknown Video Modes
Unknown Video Modes Like all other monitors, this LCD monitor is designed to work with standard video modes. However, not all video/graphic cards use only standard display modes. This LCD monitor uses state-of-the-art technology, which is designed to synchronize to any display mode.
Need help?
Do you have a question about the X-Pro GLCD15M2 and is the answer not in the manual?
Questions and answers