Advertisement
Quick Links
Advertisement
Related Manuals for Pyle PLTA180
Summary of Contents for Pyle PLTA180
- Page 2 TRBL.E OF C:ONTENTS TRBL.E OF C:ONTENTS INTRODUCTION & FEATURES ............1 FEATU RES & CONTROLS ............SPECIFICATION ................. 4 CONTROLS & FUNCTIONS ............5 ................ 6-8 SYSTEM WIRING , ..............9 TROUBLESHOOTING WI RI NG ..................... 10 - 1 -...
- Page 3 INTROCUC:TION FERTURES INTROCUC:TION Congratulations on your purchase of a PYLE amplifier. You have purchased a quality product designed and engineered to give you many years of un compromised musical service. PYLE amplifiers are designed with the latest technology available, incorporating...
- Page 4 PLTA180/580 c - p _ _ _ High SonIc .1lI! !III • • • • ..L..,. POWER & PROTECTION INDICATORS SUN SONIC FILTER Provide instant information When Crossover Mode on status of amplifier, Selector is in High Pass...
- Page 5 SPECIFICRTION SPECIFICRTION PLTA180 PLTA580 RMSat4 Ohms 200Wx2 500Wx2 MAXat4 Ohms 400Wx2 1000Wx2 At 4 Ohms Bridged 800Wx I 2000Wx I RMSat2 Ohms 350Wx2 1000Wx2 20hm 20hm Min. Speaker Impedance T.H.D 0.04% 0.04% 10Hz -35kHz. -I dB 10Hz -35kHz. -I dB...
- Page 6 INSTRL.L.RTION P"'EC:RUTIONS INSTRL.L.RTION 1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39") in length.
-
Page 7: Channel Stereo Configuration
S'r'STEM WIRING PLTA180/580 2 channel stereo configuration FRONT I>: LWIII I ..U .. C - r SubSonic ~~_. • @-!;~"l. .1lI! • • .._,- ..TO OUTPUT FROM HEAT UNIT REAR BATTER~+}--------~ SPEAKER IMPEDANCE 2-40HM SELECT REMOTE SWITCH... - Page 8 S'r'STEM WIRING PLTA180/580 2 channel bridged mode configuration FRONT I>: SubSonic C - r LWIII I ..t U .. aut @-!;~"l. 011 • • • • "" "" =- .._,- ..-' I Lc- TO OUTPUT FROM HEAT UNIT...
-
Page 9: Channel Tri-Mode Configuration
S'r'STEM WIRING PLTA180/580 2 channel tri-mode configuration FRONT I>: SubSonic C - r LWIII I ..t U .. aut @-!;~"l. 011 • • • • "" "" .._,- ..-' TO OUTPUT FROM HEAT UNIT REAR BATTER~+}--------~... -
Page 10: Troubleshooting
TROUBL.ESHOOTING TROUBL.ESHOOTING Amplifier will not power up. • Check for good ground connection. • Check that remote DC terminal has at least 3V DC. • Check that there is battery power on the terminal. • Check all fuses. • Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. - Page 11 WI"'ING ' - - - - - - - - - ' + .... 2-chennel Amplifier 2-channal Amplifier (Operetlng In (Operating In Stereo) Bridged Mono) YES! Two 4-ohm speakers, wired in stereo, Two 4-ohm speakers, wired in parallel will present a 4 ohm load to each to a bridged two-channel amplifier, channel of the amplifier.