Download Print this page

Behringer EUROPOWER PMP560M Quick Start Manual page 11

500-watt 6-channel powered mixer with klark teknik multi-fx processor, compressor, fbq feedback detection system and wireless option
Hide thumbs Also See for EUROPOWER PMP560M:

Advertisement

20
EUROPOWER PMP560M
EUROPOWER PMP560M Getting started
Step 3: Getting
With the power to all devices turned off,
(EN)
make all power, audio and speaker
started
connections. Engage the +48 V switch if
you are using condenser microphones or powered
direct boxes.
Select the appropriate speaker output
configuration with the POWER AMP A/B
selector switch.
The EUROPOWER PMP560M has two power amp
operating modes. In MAIN / MAIN mode the
PMP560M functions as a mono amplifier. In this
mode the MAIN output signal is sent to both A and
B outputs. In MON / MAIN mode the PMP560M
functions as a dual mono amplifier. In this mode the
MONITOR signal is sent to OUTPUT A and the MAIN
signal is sent to OUTPUT B.
With both the MAIN LEVEL and MONITOR
LEVEL knobs turned all the way down,
turn the mixer on.
Turn the MAIN LEVEL knob about half
way up and then adjust the volume of
connected audio sources via each
channel's LEVEL knob.
If using the PMP560M in dual mono
mode, turn the MONITOR LEVEL knob
about half way up. Use each channel's
MON knobs to adjust the amount of the channel
present in the monitor speaker(s).
If using the PMP560M in dual mono
mode, adjust the MAIN LEVEL and
MONITOR LEVEL knobs to set the overall
output volumes. The MAIN LEVEL METER and
MONITOR LEVEL METER will indicate the output
volume and whether or not the signal is clipping.
If the red LIM LEDs on the MAIN LEVEL METER or the
MONITOR LEVEL METER illuminate, turn the
corresponding LEVEL knob conuter-clockwise until
the red LED goes off.
The PMP560M has a built-in effects
processor. Follow these steps to add an
effect to one or more channels.
• Turn the FX knob up half way on each channel
that the effect will be applied.
• Press the FX button to engage the
Multi-FX processor.
• Turn the FX RETURN knob in the MAIN section
up half way. If using the PMP560S in dual mono
mode, turn the FX RETURN knob in the MONITOR
section up half way.
• Scrolll through the FX presets using the FX
selector knob, when the desired preset number is
designated in the FX PROGRAM display, press the
FX selector knob to engage the preset.
• Use the TAP tempo button to adjust the tempo of
time-based effects.
• Readjust each channel's FX knob to increase or
decrease the amount of effect applied to the
connected input source. If the METER on the
FX PROGRAM display reaches the red CLIP LED,
turn the channel FX knobs down.
If feedback occurs at the MAIN or
MONITOR outputs, engage FBQ
FEEDBACK DETECTION.
• Press the EQ and FBQ FEEDBACK DETECTION
buttons to engage the feedback detection system.
• An LED will illuminated on the EQ slider that
corresponds with the feedback frequency.
• Lower the illuminated EQ slider until the
feedback stops.
21
Quick Start Guide
Paso 3: Puesta en
Con todas las unidades apagadas,
(ES)
realice todas las conexiones de
marcha
corriente, audio y de altavoces. Si está
usando micrófonos condensadores o unidades
directas (DI box) autoamplificadas, active el
interruptor +48 V.
Elija la configuración de salida de
altavoces adecuada con el selector
POWER AMP A/B.
El EUROPOWER PMP560M tiene dos modos
operativos de la etapa de potencia. En el modo
MAIN / MAIN, el PMP560M actúa como un
amplificador mono. En este modo, la señal de
salida MAIN es enviada tanto a la salida A como
a la B. En el modo MON / MAIN, el PMP560M
se comporta como un amplificador mono dual.
En este modo, la señal MONITOR es enviada a la
salida OUTPUT A y la señal principal o MAIN es
enviada a OUTPUT B.
Con los mandos MAIN LEVEL y MONITOR
LEVEL al mínimo, encienda esta unidad.
Gire el mando MAIN LEVEL hacia la
derecha por encima de su punto medio
y ajuste después el volumen de las
fuentes audio conectadas a través del mando
LEVEL de cada uno de los canales.
Si está usando el PMP560M en el modo
mono dual, suba el mando MONITOR
LEVEL más o menos a la mitad. Use los
mandos MON de cada canal para ajustar la
cantidad de señal de canal presente en
los monitores.
Si utiliza el PMP560M en el modo mono
dual, ajuste con los mandos MAIN LEVEL
y MONITOR LEVEL el volumen de salida
global. Los medidores MAIN LEVEL METER y
MONITOR LEVEL METER le indicarán el volumen de
salida y si la señal satura o no. Si los pilotos LIM
rojos de estos medidores se iluminan, reduzca la
posición del mando LEVEL correspondiente hasta
que esos pilotos se apaguen.
El PMP560M dispone de un procesador
de efectos interno. Siga estos pasos
para añadir un efecto a uno o
más canales.
• Gire el mando FX por encima de su punto medio
en cada uno de los canales en los que vaya a
aplicar el efecto.
• Pulse el botón FX para activar el
procesador multiefectos.
• Gire el mando FX RETURN de la sección MAIN
más o menos a la mitad. Si está usando el
PMP560S en el modo mono dual, gire el mando
FX RETURN de la sección MONITOR también a la
mitad de su recorrido.
• Desplácese por los presets de efectos usando el
selector FX y cuando el número de preset que
quiera aparezca en la pantalla FX PROGRAM,
pulse el selector FX para activar dicho preset.
• Use el botón TAP tempo para ajustar el tempo de
los efectos con temporización rítmica.
• Reajuste el mando FX de cada canal para
aumentar o reducir la cantidad de efectos
aplicada a la fuente de entrada de dicho canal.
Si el medidor de la pantalla FX PROGRAM llega al
punto en que se ilumina el piloto CLIP, reduzca la
posición de los mandos FX.
Si se produce realimentación en las
salidas MAIN o MONITOR, active el
sistema FBQ FEEDBACK DETECTION.
• Pulse los botones EQ y FBQ FEEDBACK DETECTION
para activar el sistema de detección de
realimentación.
• Se iluminará un piloto en el mando deslizante
del EQ que se corresponda con la frecuencia que
está produciendo la realimentación.
• Reduzca la posición del mando
deslizante del EQ iluminado hasta que la
realimentación desaparezca.

Advertisement

loading