CyberPower OR500LCDRM1U Hardware Replacement Manual

Smart APP Intelligent LCD Series
MODEL: OR500LCDRM1U, OR700LCDRM1U, OR1000LCDRM1U, OR1500LCDRM1U
1 2
4 5
1. Remove the right side front panel.
2. Remove the three retaining screws for the cable protection cover and remove the cover.
3. Disconnect the black and red cable.
4. Remove the one retaining screw holding the battery pack in place.
5. Remove the battery pack.
6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous
steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes.
MODEL: OR1500LCDRM1U, OR2200LCDRM2U, OR1500LCDRTXL2U, OR2200LCDRTXL2U
1 2
4 5
1. Remove the right side front panel.
2. Remove the three retaining screws for the cable protection cover and remove the cover.
3. Remove the two retaining screws from the cable connectors.
4. Disconnect the black and red cable.
5. Remove the four retaining screws holding the battery pack in place.
6. Remove the battery pack.
7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous
steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes.
Smart APP SINEWAVE Series
MODEL: PR750LCDRM1U, PR1000LCDRM1U
3 1
1. Remove the right side front panel.
2. Remove the two retaining screws for the cable protection cover and remove the cover.
3. Disconnect the black and red cable.
4. Remove the one retaining screw holding the battery pack in place.
5. Remove the battery pack.
6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse sequence of the
above steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes.
MODEL: PR1500SWRM2U, PR2200SWRM2U
3 1
WARNING
BATT USING BATTERY
LOAD AVR
POWER ON
6
1. Remove the right side front panel.
2. Remove the two retaining screws for the cable protection cover and remove the cover.
3. Disconnect the black and red cable.
4. Remove the four retaining screws holding the battery pack in place.
5. Remove the battery pack.
6. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous
steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes.
2 3
4 5
2 3
WARNING
BATT USING BATTERY
LOAD AVR
POWER ON
WARNING
BATT USING BATTERY
LOAD AVR POWER
ON
4 5
WARNING WARNING
BATT BATTERY USING BATT BATTERY USING
LOAD POWER AVR LOAD POWER AVR
ON ON
Smart APP SINEWAVE Series
MODEL: PR1000LCDRT2U, PR1000LCDRTXL2U, PR1500LCDRT2U, PR2200LCDRT2U,
PR3000SWRM2U
1 2
4 5
1. Remove the right side front panel.
2. Remove the three retaining screws for the cable protection cover and remove the cover.
3. Remove the two retaining screws from the cable connectors.
4. Disconnect the black and red cable.
5. Remove the four retaining screws holding the battery pack in place.
6. Remove the battery pack.
7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous
steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes.
MODEL: PR1000LCDRTXL2Ua, PR1500LCDRTXL2U, PR2200LCDRTXL2U, PR3000LCDRT2U,
PR3000LCDRTXL2U
1 2
4 5
1. Remove the six retaining screws, and remove the front panel from the UPS.
2. Remove the two retaining screws for the cable protection cover and remove the cover.
3. Remove the two retaining screws from the cable connectors.
4. Disconnect the black and red cable.
5. Remove the three retaining screws holding the battery pack in place.
6. Remove the battery pack.
7. Install the new battery pack. Assemble the screws, cover, cable and front panel in the reverse order of the previous
steps. Charge the unit for 4-8 hours to ensure the UPS performs expected runtimes.
3
6
3
6