Advertisement
Quick Links
ENCLOSURE SUPPLY KIT (Part #7363)
The contents of this bag are for use with
Campbell Scientific's field enclosures. Please
note that some of the enclosed items should be
saved for future use.
1.
Use the #6 screws and plastic grommets to
mount additional peripherals to the enclosure
backplate. Dataloggers, power supplies, and
most peripherals are either attached to the
backplate prior to shipment from the factory
or are supplied with additional screws and
grommets. To insert the grommet, push the
points of the flanges into the center of any
square hole. To remove a grommet without
damage, remove the enclosure backplate
and use pliers to pinch the grommet flanges
together.
2.
If desired, insert the 25745 PVC coupling to
reduce the conduit's diameter to 0.5-in.
Route the sensor leads through the
enclosure conduit to the datalogger or
peripheral terminal strips.
3.
Use the cable-tie tabs and 8-in cable ties to
strain relief the cables to the side of the
enclosure as shown.
NOTE: The adhesive of the cable tie tab may not
stick during extremely cold temperatures or
extremely high humidity. In these situations,
fasten the cable-tie tab to the backplate using a
#6 screw and grommet.
4.
Strain relief the sensor leads to the
datalogger's strain-relief flanges with the 4-in
cable ties.
5.
Remove the backing tape from the humidity
indicator and attach to the side of the
enclosure as shown.
6.
Seal the gap between the sensor leads and
the enclosure conduit with sealing putty.
7.
Place two desiccant packs inside the
enclosure; reseal the other two inside the
plastic bag. Store the extra packs in a dry
area and use them to replace the two in the
enclosure during a site visit or when the 40%
ring on the humidity indicator turns pink.
CAUTION: We recommend purchasing new
desiccant instead of oven drying, which is messy
and time consuming.
Screwdriver
Screwdriver
8-in Cable Tie
8" Cable Tie
4-in Cable Tie
PVC Coupling
4" Cable Tie
PVC Coupling
The contents of the enclosure supply kit are the following.
Qty.
Part #
Description
8
505
#6-32 x .375" screws
8
6044
grommets
4
2376
3-cm cable-tie tabs
6
2207
4-in cable ties
6
4005
8-in cable ties
1
28878
humidity indicator card
2
6596
4-oz container of sealing putty
4
4905
4-unit desiccant packs
1
6290
Phillips screwdriver
1
25745
PVC coupling
4-in Cable Ties
8-in Cable Ties
and Tabs
Sealing Putty
Desiccant Pack
Desiccant Pack
Humidity Indicator Card
Humidity Indicator Card
HUMIDITY
INDICATOR
MS20003-2
EXAMINE
ITEM
IF PINK
CHANGE
DESICCANT
IF PINK
WARNING
IF PINK
DISCARD IF CIRCLES OVERRUN
AVOID METAL CONTACT
#6 Screws
Cable-Tie Tab
Cable Tie Tab
WARNING:
PS12 POWER SUPPLY
PERMANENT DAMAGE TO RECHARGEABLE
CELLS MAY RESULT IF DISCHARGED
WITH 12V CHARGING REGULATOR
BELOW 10.5 VOLTS
FUNCTION
INT
PS12 BATTERY
EXTERNAL BATTERY - DO NOT USE WITH
EXT
INTERNAL RECHARGEABLE BATTERY
CHG
CHARGE VOLTAGE PRESENT
INPUT FROM CHARGER OR SOLAR PANEL
CHG
16-26 VDC OR AC RMS: POSITIVE TO
CHG
EITHER TERMINAL, NEGATIVE TO OTHER
+12
+12
POWER TO DATALOGGER OR
12V PERIPHERALS
MADE IN USA
thia ia
thia thia
G 12V
thia thia
thia thia
Logan, Utah
thia thia
G 12V
SW 12V CTRL
POWER
CS I/O
SE
7
8
9
10
11 12
SW 12V
thia thia
IN
DIFF
4
5
6
G G H
L
AG H
L AG H
L AG E3 AG G G
5V 5V G
G
thia thia
thia thia
CR10X WIRING PANEL
MADE IN USA
thia thia
thia thia
thia thia
thia thia
SE
1
2
3
4
5
6
SDM
DIFF
1
2
3
thia thia
G G H
L
AG H
L AG H
L AG E1 AG E2 G
P1 G P2
G C8 C7 C6 C5 C4 C3 C2 C1
G 12V 12V
thia thia
EARTH
GROUND
WIRING
PANEL NO.
Grommets and screws
hold peripherals to
enclosure backplate
Printed 1/23/2013
Putty
Putty
Grommets
Grommets
#6 Screws
Humidity
thia ia
Indicator
thia thia
thia thia
thia thia
Desiccant
Packs
Advertisement
