Advertisement
Advertisement
Summary of Contents for Norcross ML100TDR ML100R ML100DR ML100tr
- Page 2 2. Clean and dry both the selected area and the face of the transducer with a weak solvent to remove any dust, grease or oil. 3. If the hull temperature is above 15º C (60º F), mix the epoxy until the color is uniform. Do not proceed if the hull temperature is below 15º...
-
Page 3: Table Of Contents
ABLE ONTENTS FIGURE 10C If the hull surface is not smooth, grind it with a disc Transducer Selection ......sander. - Page 4 Figure 20 CAUTION!!!! Always wear safety goggles and a dust mask when sanding. FIGURE 10A • This method is practical if the transducer will be located Warning: Changes or modifications to this unit not near the stern and the boat has a low deadrise angle. expressly approved by the party responsible for com Clean away any large build-up of grease and / or dirt.
-
Page 5: Transducer Selection
NorCross at 888-667-2767, or location. If the test readings differ markedly from the base- visit us on the internet at www.norcrossma-... -
Page 6: Transducer Installation
RANSDUCER NSTALLATION Figure 18 Transom Mount Transducer Installation (P23 Tr a n s d u c e r ) Never use adhesive to fill gaps between the trans- • Please follow the supplementary instruction provided ducer and the hull since Do not use in the transducer hardware package. - Page 7 IMPORTANT!!!! Before Installing the ML100DR and ML100R, it will be necessary to match the receiver to the transmitter. Figure 17 This can be completed before installing the system on the vessel by simply applying power to the trans - mitter and receiver and following steps 1 thru 3. The Outboard Inboard/Outboard receiver retains this unique code in its memory, and...
- Page 8 L o c at i o n 2. While the code is being gener- ated the display will flash Consult the boat manufacturer for the best in-hull transduc- “LEA” to indicate that it is in er placement. If this information is unavailable, follow the LEARN mode.
- Page 9 Appendix A * The mounting location of choice must be above the waterline of the vessel, and free from water spray, and/or water submersion. RANSDUCER NSTALLATION NSTRUCTIONS * A mounting location that produces the furthest range should prove to be the optimal location. IMPORTANT!!!! Please read the instructions completely * Do not mount the Transmitter within 12 inches of...
- Page 10 3. Connect the shield (bare) wire from the transmitter, to 2. If after charging the display still will not turn on, contact the shield (bare) wire on the transducer cable. NorCross at 888-NorCross for battery replacement infor- mation. Wiring of the Power Cable The Transmitter (ML100T) has no ON/OFF switch.
-
Page 11: Installing The In-Dash Wireless Display (Ml100Dr)
“E--” Appears on the Display: NSTALLING THE IRELESS ISPLAY This indicates that there is no RF signal being received from the transmitter IMPORTANT!!!! 1. Make sure that there is power to the transmitter. (A red Please follow the Setup Procedures on page 6 or green LED on the transmitter will indicate power) and read the instructions completely before proceeding with the installation. - Page 12 1. The depth is less than 2.5 feet or greater than 200 feet. Adjustable Surface Mount Bracket (see Figure 6). Please Operate the unit under normal operating specifica- see your local retailer, or contact NorCross by phone tions and check to see if it operating properly. 888-NorCross, or online at: 2.
- Page 13 ML100Series, consult the fol- lowing troubleshooting guide. If this does not remedy your 2. While holding the bezel (Figure 7A) place it over the p roblem, please contact NorCross at 888-667-2767 for display and turn counterclockwise until the bezel assistance.
-
Page 14: Installing The Portable Wireless Display (Ml100R)
To purchase accessories visit your local marine 1. Find a suitable mounting location for the charging retailer, contact NorCross at 888-NorCross, or visit stand and fasten utilizing the two mounting holes. us on the web at www.norcrossmarine.com... -
Page 15: Operating The Transmitter (Ml100T)
If echoes are not received from the transducer, the trans- mitter LED will flash in either red or green color depending Since NorCross Marine Products continually strives to provide the finest prod- on which RF channel has been selected. Please refer to ucts in the world, we reserve the right to make changes or improvements in the troubleshooting section to cor rect this situation. - Page 16 Both the If upon receipt of the defective unit NorCross determines ML100R and ML100DR displays that the defect is not covered under the NorCross Limited will read “E” (Figure 11) if the Warranty, we will contact you about your repair options stored code does not match the and associated costs.
- Page 17 “DOWN” keys at the same time for 5 seconds. When tomer, however, is responsible for any costs associated the display turns on release the keys. with returning the unit to NorCross. This warranty is void if damage or malfunction is due to abuse, misuse, acci- Figure 12...
- Page 18 - Securely pack the unit, and mail prepaid via insured post 5. The display will return to the normal mode automati- NorCross Marine Products, Inc., Wa rr a n t y cally after five seconds. Department, 1629 Prime Court - Suite 800,Orlando, FL 32809.
- Page 19 2. The "up" key will increase the selected value. The 2. The "UP" key will increase the selected value. The "down" key will reduce the value. Pressing either key "DOWN" key will reduce the value. Pressing either key will change the value in 1-foot increments. Holding will change the value in 1-foot increments.
- Page 20 Figure 4...
-
Page 21: Operating The Wireless Displays (Ml100R, Ml100Dr) 15 Warranty Information
IMPORTANT!!!! Before Installing the ML100DR and ML100R, it will be necessary to match the receiver to the transmitter. This can be completed before installing the system on the vessel by simply applying power to the trans- mitter and receiver and following steps 1 thru 3. The receiver retains this unique code in its memory, and will only need to be relearned if the channel on the transmitter is changed.
Need help?
Do you have a question about the ML100TDR ML100R ML100DR ML100tr and is the answer not in the manual?
Questions and answers