Advertisement

Soundweb
London
TM
BLU-101 Installation Guide
18-0770-B
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SoundwebTM London BLU-101 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for BSS Audio SoundwebTM London BLU-101

  • Page 1 Soundweb London BLU-101 Installation Guide 18-0770-B...
  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS THE APPARATUS SHALL NOT bE ExPOSED TO DRIPPING OR SPLASHING The symbols shown above are internationally accepted symbols LIqUID AND NO ObjECT FILLED WITH LIqUID, SUCH AS vASES, SHALL that warn of potential hazards with electrical products.
  • Page 3: Declaration Of Conformity

    IMPORTANT SAFETY INSTRUCTIONS DECLARATION OF CONFORMITY U.K. MAINS PLUG WARNING Manufacturer’s Name: BSS Audio A molded mains plug that has been cut off from the cord is unsafe. Discard Manufacturer’s Address: 8760 S. Sandy Parkway the mains plug at a suitable disposal facility. NEVER UNDER ANY...
  • Page 4: Regulatory Information

    This equipment must be earthed. It should not be necessary to remove any protective earth or signal cable shield connections to prevent ground loops. Any such disconnections are outside the recommended practice of BSS Audio, and will render the EMC or safety certificate void.
  • Page 5: Front Panel

    Front panel Input/Output channel monitoring Each channel has the following LED indicators: Clip Indicates clipping in the analogue domain for each input or output channel. The LED will illuminate at +18.5dB. Signal The Signal LED will illuminate for each input or output channel when the signal reaches or exceeds the signal threshold of -20dB.
  • Page 6 Audio cable wiring All audio and GPIO connections to the BLU-101 are via Klippon pluggable terminal block connectors (also known as BL, Phoenix or Combicon). The BLU-101 includes 3-way female Klippon connectors for individual channels. Audio Input and Output wiring convention Soundweb products provide cable shielding ‘back from the destination’...
  • Page 7: Rear Panel

    BLU link 100-240V ~ 50/60Hz, 50W CONTROL THIS EQUIPMENT MUST BE EARTHED OUTPUTS INPUTS MANUFACTURED IN THE USA BY BSS AUDIO LOCATE RS232 ETHERNET AC Mains AC Mains input to the universal switched-mode power supply, operates over a wide range of AC input voltages from 100V to 240V, 50/60Hz.
  • Page 8 Automatic Gain Control (AGC) and Noise Cancellation (NC) are also provided per AEC algorithm. AGC ensures that microphone levels remain at an optimum level, and NC removes steady state noise (such as from a projector fan or air conditioning device) from the signal path.
  • Page 9 OPTO Output In addition to the six standard LOGIC OUTPUTS, there is an isolated output, which fails safe (open circuit) if the unit becomes faulty. 47kOhm 10K-100kOhm linear unconnected lad- lad- switch switch 2 wire mode 3 wire mode +supply relay relay ground...
  • Page 10: Technical Specifications

    Technical specifications FRONT PANEL LED INDICATORS Signal Present, CLIP, 48V (input only) Other: Control link status and activity for Ethernet and RS-232 connections (COM); Device configuration status (STAT); Error (ERR); Power/Locate (PWR) ANALOGUE INPUTS: 12 electronically balanced on Phoenix/Combicon removable screw connectors Mic/Line Inputs: Nominal gain 0dB, electronically switchable up to +48dB, in +6dB steps...
  • Page 11 Please contact BSS Technical Support for more information on purchasing replacement parts or product service. BSS Audio has a policy of continued product improvement and accordingly reserves the right to change features and specifications without prior notice.
  • Page 12 BSS Audio 8760 South Sandy Parkway Sandy, Utah 84070 801-566-8800 www.bssaudio.com Printed in the USA...

This manual is also suitable for:

Blu 100 soundweb london

Table of Contents