Summary of Contents for SAF OPAL Ethernet IP Interface MS6 SERIES
- Page 1 Opal Pro to Mod TCP Opal Pro MS6 SERIES AB Ethernet IP Interface Users Manual Revision 1.00 Page 1...
- Page 2 Opal Pro to Mod TCP Page 2...
-
Page 3: For Your Safety
FOR YOUR SAFETY Only qualified personnel should install this equipment, after first reading and understanding all the information in this manual. All instructions should be strictly adhered to. The user should consult Brock Solutions or a SAF OPAL Starters supplier for clarification of the contents of this manual should any doubt or questions arise. - Page 4 Opal Pro to Mod TCP Page 4...
-
Page 5: Table Of Contents
Opal Pro to Mod TCP Table of Contents INTRODUCTION ... 6 HARDWARE ... 6 JUMPER SETTINGS... 6 LED INDICATORS ... 7 OPAL PRO PARAMETER SETTINGS ... 8 I/O CONFIGURATION... 10 Page 5... -
Page 6: Opal Pro To Mod Tcp
Opal Pro to Mod TCP Opal Pro to Mod TCP Introduction The Opal Pro can be monitored and controlled over an Ethernet communication network using the AB Ethernet IP protocol. The Opal Pro connects to the Ethernet network through and optional Ethernet card that is mounted on the main Opal Pro control card (CA530). -
Page 7: Led Indicators
LED Indicators Two bi-colour (red/green) LED indicators are mounted beside the network connector. The upper LED indicates the Ethernet interface card status. LED State Flashing Red Solid Red Flashing Green Solid Green Amber (Red/Green) The lower LED indicator indicates the Ethernet Network status. LED State Flashing Red Flashing Green... -
Page 8: Opal Pro Parameter Settings
Opal Pro to Mod TCP Opal Pro Parameter Settings The parameters in the Opal Pro used to configure the Ehernet interface card (group 14) are only accessible if a Ethernet interface card is installed. The parameter settings are as follows: Opal Pro Parameter 2.02 Comm Module... - Page 9 15.04 Comm Fault Enable Disable 15.05 Comm Fault 0.1 to 5.0 Time secs If parameters in group 14 are modified the changes do not take effect until the control power for the Opal Pro is turned off and then back on again. Opal Pro to Mod TCP Enable –...
-
Page 10: I/O Configuration
Opal Pro to Mod TCP I/O Configuration The Opal Pro supports 4 input words and 51 output words. Their description is as follows: Input Words Ethernet (Polled) Word 1 Output Word 0 Word 2 Output Word 1 Word 3 Output Word 2 Word 4 Output... - Page 11 Output AB Ethernet Words (Polled) Word 1 Input Word 0 Word 2 Input Word 1 Word 3 Input Word 2 Parameter AB Ethernet 1.01 Input Word 3 1.02 Input Word 4 1.03 Input Word 5 1.04 Input Word 6 1.05 Input Word 7 1.06 Input Word 8...
- Page 12 Opal Pro to Mod TCP 1.07 Input Word 9 1.08 Input Word 2.01 Input Word 2.02 Input Word 2.03 Input Word 10.01 Input Word 10.02 Input Word 10.03 Input Word 10.04 Input Word 10.05 Input Word 10.06 Input Word 10.07 Input Word 10.08 Input Word...
- Page 13 12.01 Input Word 13.01 Input Word 13.02 Input Word 13.03 Input Word 14.01-14.06 Input Word 31- Input Word 36 14.07 Input Word 14.08 Input Word 14.09 Input Word 14.10 Input Word 14.11 Input Word 14.12 Input Word 14.13 Input Word 14.14 Input Word 14.15...
- Page 14 Opal Pro to Mod TCP NOTE: The Opal Pro must have firmware version 1.70 or higher. Page 14...
Need help?
Do you have a question about the Ethernet IP Interface MS6 SERIES and is the answer not in the manual?
Questions and answers