Integra KEY-5.7 Instruction Manual
  1. Manuals
  2. Brands
  3. Integra Manuals
  4. Keypad
  5. KEY-5.7
  6. Instruction manual
Integra KEY-5.7 Instruction Manual

Integra KEY-5.7 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Keypad
KEY-5.7
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KEY-5.7 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Integra KEY-5.7

Summary of Contents for Integra KEY-5.7

  • Page 1 Keypad KEY-5.7 Instruction Manual...

  • Page 2: Precautions

    Precautions 1. Read these instructions. for compliance could void the user’s authority to operate the equipment. 2. Keep these instructions. Note: This equipment has been tested and 3. Heed all warnings. found to comply with the limits for a Class B 4.

  • Page 3: Table Of Contents

    Table of Contents Introduction Precautions ........2 The Integra KEY-5.7 keypad is IR learning Introduction........3 and includes a host of features to simplify/ Features .......... 4 enhance the amplifier and source equipment Part Names and Function....5 control. Installation ........8 When used with an Integra MZA-4.7...

  • Page 4: Features

    • Long Press timing and IR code repeats are programmable using Integra Keypad Manager. • IR codes using the “HEX” code format can be used to program the KEY-5.7. Learnt IR codes can also be converted to the “Hex” code format.

  • Page 5: Part Names And Function

    Part Names and Function Chassis Key Cap bracket Source Keys Set Key Membrane Keypad SKIP USB socket Learning IR sensor -VOL VOL+ System LED & IR Receiver Volume indicator...
  • Page 6 Part Names and Function —Continued Cover Plate Infra-Red Window...
  • Page 7 Part Names and Function —Continued Key Cap Membrane Tuner Cable USB Cable Flush Box screws iPod iPod2 Sirius TIVO Request Imerge TAPE Lights RJ45 Connector Room2 PROJ SCRN CAM1 CAM2 CAM3 CD-ROM...

  • Page 8: Installation

    Installation The KEY-5.7 chassis mounts directly to the wall surface. The following steps outline the installation procedure: • Cut out the required mounting hole in the wall above the flush-box. • Terminate a RJ45 plug to the CAT5E cable see wiring instructions on page 8.

  • Page 9: System Wiring

    System Wiring CAT5E cable terminated with a RJ45 plug is used to connect to the KEY-5.7. Use the standard 568-B color code for the CAT5E termination: 1 2 3 4 5 6 7 8 Pin # Wire Color Keypad function...
  • Page 10 System Wiring — Continued Connecting to an Integra Multi-Zone amplifier MZA-4.7 KEY-5.7 keypads are wired to the MZA-4.7 Interface port. Integra controllers - keypad’s - may be parallel connected. IR emitters plug into the IR outputs and are fixed to the source equip- ment’s IR windows.

  • Page 11: Manual Programming

    The SET Key is used along with the Source Keys to put the keypad into various programming modes. The SET key is pushed first - System LED flashes Green followed by the relevant source or function key. The functions are: Learn Mode Integra Mode Macro Mode Long Press Mode SKIP Reset Standby...
  • Page 12 LED stops flashing (Ready to receive an been learned, push the SET key to exit. IR code). Place the donating remote approximately Integra MODE = SET + S2 80mm away from the Learning IR sensor and push the remote control key, holding down Push SET followed...
  • Page 13 OFF the zone twice. The keypad detects Learn. the amplifier and programs itself to address After learning two commands in Macro Alter- the zone and device. Integra mode automati- nating mode the keypad automatically exits. cally exits. After learning a string of sequential IR codes...
  • Page 14 Manual Programming —Continued LONG PRESS MODE = SET + S5 RESET = SET + S6 + S6 This mode adds a sec- To reset the keypad, ond function to a key deleting all Learnt IR already programmed. commands push SET The second function followed by two S6 will be sent by the...
  • Page 15 Manual Programming —Continued SOURCE INDICATOR DIMMING = Push SET, then push the key to toggle through OFF, 25%, 50% and 100% levels. SET + –VOL Exit by pushing the SET key. The source indicator brightness may be adjusted: Push SET, then push – VOL to cycle BACKLIGHTING TOGGLE = through 25%, 50% and 100% levels.

  • Page 16: Troubleshooting

    No control at all. – Ensure the IR emitter is directly over the source equipment’s IR window. – The KEY-5.7 forms just one part of an IR – Check to see if the source gear can be system. There are potential issues with...
  • Page 17 Troubleshooting —Continued keypad is functioning correctly ie. Source key flashes when a key with learnt function is pressed. Try replacing the IR emitters - these are readily dam- aged if connected across the Controller Interfaces power supply. Keypad does not track the MZA- 4.7.

  • Page 18: Specifications

    Specifications IR Learning Wiring Compatible with virtually all brands of remote Up to 200 m of CAT5E home run cable. controls using carrier or modulation frequen- Voltage Current cies between 20KHz and 500KHz. 12 V DC ±3 V Also capable of learning non-modulated pulse Typically 50 mA, Max=120 mA codes with a minimum pulse width of 10 µs.
  • Page 23 Memo...
  • Page 24 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho D0610-1 Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124...

Table of Contents