Watching Tv; Turning On/Off The Power; Initial Installation - Sharp Aquos LC-80LE857U Operation Manual

Watching TV

Turning On/Off the Power

POWER
POWER (On/Standby)
Press POWER on the TV or on the remote control
unit to turn the power on.
NOTE
• The Initial Installation starts when the TV powers on for
the fi rst time. If the TV has been turned on before, the
Initial Installation will not be invoked. For changing the
settings of the Initial Installation, perform "EZ setup" on
the Initial Setup menu on page 28.
Press POWER on the TV or on the remote control
unit again to turn the power off.
• The TV enters standby and the image on the
screen disappears.
NOTE
• If you are not going to use this TV for a long period
of time, be sure to remove the AC cord from the AC
outlet.
• Weak electric power is still consumed even when the
TV is turned off.
16

Initial Installation

When you turn on the TV for the fi rst time, it will
automatically memorize the broadcasting channels
available in the region where you live. Perform the
following steps before you press POWER on the
remote control unit.
1. Insert the batteries into the remote control unit.
(See page 10.)
2. Connect the antenna cable to the TV. (See page 10.)
3. Plug in the AC cord to the AC outlet. (See page 9.)
Language (Language setting)
Select from among 3 languages: English, French and
Spanish.
1 Press a/b to select the desired language listed
on the screen, and then press ENTER.
Language
Location & Time
TV Location
English
Antenna & Cable/STB
Français
Air/Cable
Español
CH Search
Network
Completed
Location & Time
Make settings for the country, area and time zone
where you use the TV.
2 Press a/b to select "United States", "Canada"
or "Mexico", and then press ENTER.
United States
Canada
Mexico
3 Press a/b to select the time zone where you
are using the TV, and then press ENTER.
Example
EST
CST
MST
PST
AKST
HAST
• The time zone differs depending on the selected
country.
• The factory preset value is the time zone for the
capital of the selected country.
4 Press a/b to select the Daylight Savings Time,
and then press ENTER.
Auto
Manual
Off
• "Auto" is the default selection.
TV Location
Select "Home" or "Store" for the location where
you plan to install the TV. This product qualifi es for
ENERGY STAR 1 in Home mode default setting.
*
5 Press c/d to select "Home" or "Store".
Press ENTER to enter the setting.
Select
Home
Store
Home: "Power Saving" is set to "Advanced", and AV
MODE is set to "STANDARD (ENERGY STAR)* 1
Store: "Power Saving" is set to "Off" and AV MODE
is set to "DYNAMIC (Fixed)". Picture Reset and
Feature Demo can be set.
Picture Reset: AV MODE will be set to
"DYNAMIC (Fixed)" regardless of whether
Picture Reset is "On" or "Off".
• If you select "On" and there is no operation
for 30 minutes:
- AV MODE will be reset to "DYNAMIC (Fixed)".
- When a 3D signal is detected, 3D images
will switch to 2D images. (For the LE857U,
LE757U, LE755U, LE657U and LE655U
models)
• When "Off" is selected:
- AV MODE will be set to "DYNAMIC (Fixed)".
Feature Demo: When "On" is selected, after all
the settings are completed, the Feature Demo
screen is displayed if there is no operation for
several minutes.
NOTE
• ENERGY STAR qualifi cation is based on AV MODE
"STANDARD (ENERGY STAR)".* 1
Antenna & Cable/STB
Select the type of connection you will use to watch TV.
Press c/d to select "Antenna & Cable" or "Set-
6
top box", and then press ENTER.
Antenna & Cable Set-top box
To watch TV via an antenna or cable connection
(without using a set-top box):
Select "Antenna & Cable", and then go to step 7.
To watch TV via a set-top box:
1Select "Set-top box", and then press ENTER.
2Please make sure your set-top box is turnd on,
and then press ENTER.
3To watch TV, select the input source
corresponding to the terminal connected to the
set-top box. When doing so, you must make the
setting to skip "TV". Press c/d to select "On",
and then press ENTER.
On Off
• When this is set to "On", the channel on the TV
cannot be changed using the remote control
unit or menu. (e.g. CH / , Favorite CH,
etc.)
• See page 26 for details on the Input Skip
function.
4Press INPUT to select the input source
corresponding to the terminal connected to the
". set-top box. Make the necessary settings on the
connected external equipment.
• See the operation manual of the connected
equipment for setting up the equipment.
Air/Cable (Antenna setting)
Make sure what kind of connection is made with
your TV when selecting "Air" or "Cable".
7 Press c/d to select "Air" or "Cable".
Press ENTER to enter the setting.
Air
Cable
NOTE
• *1: Except for LC-90LE657U