Advertisement
TempJate
instructions
Drilling
from
inside the cabinet
If you
cannot
drill
from
inside
the
cabinet,
see "Drilling
from
under
the
cabinet"'
section.
If the cabinet
does
not have
a partition
or
you
are not installing
under
two
adjoining
cabinets:
Piace tempiate
inside
the cabinet
so
that the front
iine of theTempiate
A wHi
be aligned
with
the front
edge
of the
cabinet.
If necessary,
cut some
areas
of
the tempiate
in order
to make
it fit
property
within
cabinet.
See NOTE
at bottom
of page.
If the cabinet
has a partition
or you
are
installing
under
two
adjoining
cabinets:
1. CutTemphte
B from
template
A along
the dotted
line.
2. Cut Template
A into two
pieces
to fit
each side
of the
partition,
3. Position
one piece
ofTemplate
A inside
cabinet
making
sure
the front
line
is
aligned
with
the front
edge
of the
cabinet.Tape
in place.
Template B
4. PositionTemplate
B in front
of the
cabinet
so that
the hole centerline
is
aligned
with
the hob
centerline
of the
Template
A piece
positioned
in Step
3
above.
5. Position
the other
piece
of Template
A
inside
the adjacent
cabinet
opening
so
that the hole
centerline
aligns
with
the
hole
centerline
onTemplate
B.Tape
in
place.
If you
have
followed
the
instructions
properly,
the distance
between
the right
and left
hob
centerlines
will
be 12-7/8"
(32.7 cm).
other piece of
I i
Te_t
e_
Template__
__
_
12-7/8"
/
(32.7 em)
See NOTE
to right,
Drilling
from
under the cabinet
if the cabinet
does
not have
a front
frame
exending
below
the cabinet,
there
is no
partition,
or you
are not installing
under
two
adjoining
cabinets:
TapeTemplate
A to the underside
of
cabinet
so the front
line of template
will
be aligned
with
the front
edge
of
the cabinet.
If necessary,
cut some
areas
of the template
in order
to make
it fit properly
on the
underside
of
cabinet.
See NOTE
at bottom
of page,
if cabinet
has only
a front
frame
extending
below
the cabinet
bottom
and
no partition:
Measure
the thickness
of the frame,
Fold template
along
guide
line that
matches
the frame
thickness.
Place
the
folded
edge
of template
against
the
back side
of front
frame
on the
underside
of the cabinet,Tape
in place.
See NOTE
at bottom
of page_
If the cabinet
has a partition,
you
are
installing
under
two
adjoining
cabinets,
or there
is a side frame
as shown:
1. CutTemplate
B from
template
A
along
the dotted
line.
2. Cut Template
A into
two
pieces
to fit
each side of the partition
or adjoining
cabinets.
3_
Position
one piece
of Template
A
under
cabinet
making
sure
the front
line is positioned
against
the back
side of front
frame
on the underside
of the cabinet,Tape
in place,
front frame
partition or
of cabinet
_Jadioining
c[abh_ets
4_
5_
PositionTemplate
B toward
the
rear
of the cabinet
so that the hole
centerline
is aligned
with
the hole
centerline
of theTemplate
A piece
positioned
in Step
3 above.
Position
the other
piece
of Template
A
under
the adjacent
cabinet
opening
so that the hole
centerline
aligns
with
the hole
centerline
onTemplate
B,
Tape
in place.
If you
have
followed
the instructions
properly,
the distance
between
the right
and left hole
centerlines
will
be 12-7/8"
(32.7 cm}.
]l
]l
Jl
See NOTE below.
NOTE:
For any of the template
instructions
used,
whenTemplate
A is properly
installed,
the distance
from
the front
edge
of the cabinet
with
cabinet
door(s)
open
to the centerlines
of the front
holes
will
be 2-1/16"
(5.2 cm).
Template
A
2-1/16"
(5.2 em)
Return
to Step
3 of 'qnstallation
steps/'
Part No. 8204864/3828WSU0311
Printed in China
© 2004Whirlpool
Corporation.
2/2004
Advertisement
