Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tanaka 945601 - TOB 120
Summary of Contents for Tanaka 945601 - TOB 120
- Page 1 Owners Manual 711 4193...
- Page 2 A Message to Tanaka Customers ... Welcome to the world of Tanaka equipment, If service is required, be prepared to supply are pleased that you have purchased the best service person with the Model and Serial Number equipment available. care...
-
Page 3: Safety Precautions
Use only replacement parts designed for this unit. PadNumber045606 © Tanaka... - Page 4 Repair odorless and deadly gas. DO NOT run motor damage before restarting unit. (See your Tanaka enclosed or poorly ventilated areas. Dealer.) Before starting, make sure unit is properly secured After striking a submerged object, stop motor, wait to boat transom using clamp stud handles.
-
Page 5: Maintenance And Storage
DO NOT operate to motor leg. unit if brake does not operate properly. Have unit serviced by your Tanaka dealer before operating. When transporting unit in a vehicle, secure it to prevent turnover which could result... -
Page 6: Fuel Mixture
Dealer Preparation for Operation Customer Note: Your Tanaka Dealer is expected to complete these preparation steps and review important information, including this manual, with you before or upon delivery of this unit. Preparation information is included here so that you and your dealer may review it together. -
Page 7: Gear Housing
Complete Outboard Motor Warranty Registration Advise customer on adjustments propeller Form and mail original copy to Tanaka. shear pin replacement. Give customer his Owner's Manual and advise him Warranty is registered under model and serial number found on label attached to unit. -
Page 8: Operation
Controls and Features (Cont.) 1. Starter Handle Cavitation Plate Reverse Driving Lock 2. Choke Lever Dual Automatic Fill and Draln Plug Power Head Gear Housing Clutch Housing Fuel Sediment Bowl 4. Spark Plug Gear Housing Cover Cotter Pin and Filter 5. -
Page 9: Tilt Adjustment
Premix Tanaka instructions Tilt Adjustment container. If Tanaka oil is not available, select quality 2 cycle BIATC (Boating Industry Association Cycle) approved unleaded Motor tilt must be adjusted to propel boat through the water with an even keel. -
Page 10: Steering Adjustment
Operation (Cont.) ..WRONG __BOW 1. Steering Tension Bolt Figure 6: Tilt Adjustment & Transom 2. Tilt Lock Bracket Pin & Hair Mounting Motor cavitation is a condition where turbulent air Figure 7: Steering Tension Adjustment passes by the propeller resulting in an increase motor... - Page 11 Operation (Cont.) Fuel Model 300 When starting motor, open Air Vent Screw on Fuel Move twist grip handle to half throttle position. Filler Cap. Open Fuel Shut Off Valve. Choke if starting a cold motor, move Choke Lever to its START (ON) position: After motor...
-
Page 12: Rewind Starter
Operation (Cont.) :< Rewind Starter STOPPING Grasp Rewind Starter handle and pull rope slowly For normal stopping, move Throttle Lever or twist until you feet some resistance, then pult rope with grip to IDLE position and allow motor to run at idle a rapid stroke and allow rope to rewind... -
Page 13: Operating Tips
Have unit serviced as soon as possible. Figure 11: Tilting Motor Lubrication and Maintenance Your Tanaka Dealer will be happy to provide any service required to keep your Outboard Motor operating at peak efficiency. • , iill CAUTION:... -
Page 14: Shear Pin Replacement
Lubrication and Maintenance (Cont.) Shear Pin Replacement replace shear pin, remove cotter pin which holds propeller against shear pin. Remove propeller inspect damage. Replace Insure that motor stopped, wire from spark necessary. Lubricate shaft with lithium grease. plug is removed, and unit has cooled down. -
Page 15: Motor Cooling
Lubrication and Maintenance (Cont.) Motor Cooling Ignition System motor is air cooled, and air must circulate Test for faulty ignition system by removing spark freely around motor and over cooling fins plug from engine. Connect plug wire and hold plug cylinder head to prevent overheatingl... - Page 16 IMPORTANT: To prevent damage to carburetor, have idle adjustment performed by an trained professional. Tanaka company recommends that you take your unit to your Tanaka dealer when these adjustment are necessary. Model Carburetor has a fixed high speed jet screw which is preset at factory and does not need adjustment.
- Page 17 At this point, piston is covering intake an exhaust ports of the chamber. If Tanaka 2 cycle oil is not used, we recommend stabilization of the fuel With an anti-oxident fuel Clean unit thoroughly. Touch up all areas to stabilizer, such as Sta-Bi! ®,a product of Gold Eagle...
-
Page 18: Specifications
Specifications TOB-120 TOB-300 BorelStroke ..... 1,19" x 1.19" (30 x 30mm) Bore/Stroke ..1,61" x t.50" (41 x 38mm) Displacement !.39 cu.in. (22cc) Displacement ....3;05 cu.in, (50cc) Motor Bearings " Ball Motor Bearings ......Ball Motor 2 cycle air cooled Motor_ .. - Page 19 The above warranties are extended to the first end user, and no warranty is made nor authorized to be made assignable on resales by the first and user• Tanaka makes no warranty with respect to trade accessories not manufactured by it or sold by it• Such _ade accessories are subject to the =-amanty policy of their respective manufacturers.
- Page 20 Tanaka , . Marketed Exclusively by: International Sales & Marketing 22461 72rid Ave. S. Bldg #3 Kent, 98032 Phone (206) 395-3900...