Page 2
• Do not twist the VOLTAGE SELECTOR switch with excessive force as this may cause damage. • If the VOLTAGE SELECTOR switch does not move smoothly, please contact a qualified service technician. AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 2 ® CAUTION FUSE CONTROLS ADJUSTMENTS...
15. Servicing - The user should not attempt to service the CD Player beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 3 ® been damaged. spilled into the CD Player. or water.
• The control panel's LCDs are designed to be clearly visible within the angles shown in Figure 2. Mount the control unit so that the visual angle is within this range. AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 4 ® Fig. 2...
LCD DISPLAY (27). Next, press PLAY (25) on CD player A and CUE (15) on CD player B. After Player A’s single track is finished Player B will automatically cue and play. After Player B’s track is finished, the DCD-PRO500 will “Flip Flop” back to Player A etc. etc.
13. JOG WHEEL - (INNER WHEEL) This jog wheel serves two functions depending on the operating mode you are work- ing in. AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 6 ® MEMORY CUE 2...
Page 7
34. SINGLE INDICATOR - This indicates that the CD drive is in single play mode, the track will play once and return to CUE mode. If the single indicator is not on the drive is in con- AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 7 ®...
Page 8
54. CONTROL - Connect mini-plug from CONTROL out on rear of CONTROL UNIT to a mixer’s CONTROL out. This feature is available on all mixers with Fader “Q” Start (see Q” Start Control p.5). AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 8 ® Figure 7...
CUE POINT is changed to the new starting point. If you pause during playback this also sets the new CUE POINT. American DJ AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 9 ® 5 in. / 12cm disk Fig.
Page 10
Press the OUT/EXIT BUTTON (18) to return to normal play from the the American DJ OP/CL PROG. SGL/CTN. TIME Q-Start SHUTTLE Fig. 13 AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 10 ® OP/CL PROG. SGL/CTN. TIME Q-Start SHUTTLE Fig. 14 8%.12%.16%...
Page 11
You may now press one of the six (6) CUE BUTTONS (4) to store your cue point into memory. After pressing one of the CUE BUTTONS (4), the button you selected will flash briefly American DJ AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 11 ®...
Page 12
4. The LCD DISPLAY (27) will now indicate a LOOP NUMBER 1~6 (41) that corresponds with the CUE BUTTON (4) you selected in the previous step. This number indicates which CUE BUTTON (4) stored the loop you just programmed. American DJ AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 12 ®...
• Use the PITCH SLIDER (12) to adjust the pitch until same BPM is read in both units. • Because the BPM’s are approximate reading you may need to use the PITCH BEND BUTTONS (26 & 28) to adjust for small variances in pitch. American DJ AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 13 ®...
If a CD is left in the player and the remote has been disconnected, plug power cable in, turn on power and take out CD. American DJ Fig. 18 Switch off the power after the disc holder has been closed with the OPEN/CLOSE button. AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 14 ® Fig. 19...
4.5 lbs. / 2 kg 5 to 35˚C 25 to 85% -20 to 60˚C +/-8%, +/-12% or +/-16% 1/75 sec. (1 subcode frame) AUDIO • DCD-PRO500™ INSTRUCTION MANUAL • PAGE 15 ® (41 to 95˚F) (no condensation) (4 to 140˚F)
Need help?
Do you have a question about the DCD-PRO500 and is the answer not in the manual?
Questions and answers