Summary of Contents for Gold Vision GV-S42P
- Page 1 PLASMA MONITOR (DISPLAY) OPTIONS INSTRUCTION MANUAL PLASMA MONITOR (DISPLAY) GV-S42P SPEAKER PLASMA MONITOR(DISPLAY) WALL HANGER UNIT GV-H42G PLASMA MONITOR (DISPLAY) STAND GV-S42T...
-
Page 2: Instruction Manual
PLASMA MONITOR (DISPLAY) SPEAKER Thank you for purchasing the Gold vision Plasma Display Speakers. These speakers are specifically designed only for the Gold vision Plasma Display. To ensure the safe operation of the unit, please read these instructions before installing. - Page 3 TABLE OF CONTENTS 1. Check for enclosed parts ......2 2. Important Safety Instructions ...... 3 3. Assembly Instructions ......... 5 Using speakers when attached to the plasma display 2) Using speakers on its own stand...
- Page 4 PLASMA DISPLAY SPEAKER 1. PLEASE CHECK THE FOLLOWING ITEMS SHOWN BELOW M4 SCREWS SPEAKER (16) SPEAKER WIRES VIBRATION ABSORBENT SPONGE CLAMP WIRE FIXED BRACKETS...
-
Page 5: Important Safety Instructions
Do not use the speakers with other products. Do not alter or modify any parts These speakers are specifically manufactured to be used with the Gold vision Plasma display to enhance your listening pleasure. (Failing to do so may cause the unit to fall and break) - Page 6 PLASMA DISPLAY SPEAKER PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING When assembling, be sure to use the enclosed Please be careful not to stain the speakers with parts and make sure all parts are tightly any gas or oil. screwed as instructed.
-
Page 7: Assembling Instructions
3. ASSEMBLING INSTRUCTIONS USING SPEAKERS WHEN ATTACHED TO THE PLASMA DISPLAY ATTACHING VIBRATION ABSORBENT SPONGES TO SPEAKERS Clean the surface with soft, lint-free cloth Attach the sponge to the side of the where sponges will be attached. speaker that will be attached to the plasma display. - Page 8 PLASMA DISPLAY SPEAKER INSTALLING SPEAKERS TO THE PLASMA DISPLAY Place a protective covering over the surface you will be working on and lay the plasma display as shown below. . Take the speakers with fixed brackets to the back of the plasma display. Place the hooks onto the fixed brackets to the squared holes in the back of the plasma display.
- Page 9 CONNECTING SPEAKER WIRES Take the speaker wire(2) and use the red cord to connect to and fro (+) inputs, and use the black cord to connect to and fro (-) inputs. Note Please be sure to connect red cord with (+) and black with (-); otherwise, speakers will not produce clear sounds.
- Page 10 PLASMA DISPLAY SPEAKER INSTALLING SPEAKERS TO ITS OWN STAND OR UNINSTALLING SPEAKERS FROM ITS OWN STAND UNINSTALLING SPEAKERS FROM ITS OWN STAND. Speaker Please, use a coin to loosen the special screws. Stand INSTALLING SPEAKERS TO ITS OWN STAND. Please be sure to have the vibration absorbent sponge onto the side of Use a coin to secure...
- Page 11 PLASMA MONITOR (DISPLAY) WALL HANGER UNIT Thank you for purchasing the Gold vision Plasma Display Wall Hanger Unit. This wall unit is specifically designed for use with the Gold vision Plasma Display. To ensure the safe operation of the unit, please read these instructions before installing.
- Page 12 TABLE OF CONTENTS 1. Check for enclosed parts ......2 2. Important Safety Instructions ......3 3. Assembly Instructions ........6 4. Adjusting angles after installation ....12 To install the wall hanger unit, Please consult an Authorized service center first.
- Page 13 PLASMA DISPLAY HANGER UNIT 1. PLEASE CHECK THE ITEMS SHOWN BELOW FRAME SET A FRAME SET B CONNECTING FRAME CONCRETE WALL ANCHOR M5 SCREWS (20 MM) WALL SCREWS PAPER PATTERN PLAN M5 SCREWS (30MM) Paper pattern plan...
- Page 14 Do not alter or modify any parts Do not use the wall hanger unit with other products. This wall hanger unit is specifically designed to fit the Gold vision Plasma Display. (Failing to do so may cause the unit to fall and break)
- Page 15 PLASMA DISPLAY HANGER UNIT PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING Special care is needed when installing onto the When installing, please wear working gloves. wall due to its weight (35Kg) When installing on a concrete wall Please be sure to use the enclosed concrete anchors.
- Page 16 PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING When installing, please use the size referenced below to choose a place, and attach the paper pattern plan to the wall. 519.5 519.5 Paper pattern plan Measurement unit : mm It is important to use the paper pattern plan to choose the proper place; otherwise, it can result in damage to the wall and you will not be able to install the unit When installing, please allow at least 15 cm at the top, bottom, left and right on the wall, and clear all items away from where the unit will be.
- Page 17 PLASMA DISPLAY HANGER UNIT 3. ASSEMBLING INSTRUCTIONS PREPARATION WHEN THE PLASMA DISPLAY IS ATTACHED TO THE STAND TO DETACH THE STAND FROM THE PLASMA DISPLAY To avoid unwanted marks on the unit, place Unscrew the secured 4 screws completely a protective covering over the surface you and Pull the stand away from the plasma will be working on and lay the plasma display to detach.
- Page 18 INSTALLING THE WALL FRAME SET A ON THE PLASMA DISPLAY HOW TO DISPOSE OF THE PLASMA MONITOR WRAPPER First discard the wrapping band and Afterwards, dispose of the Styrofoam raise the top box to open. and remove the vinyl covering. HOW TO INSTALL FRAME SET A ON THE UNIT To avoid unwanted marks on the unit, place Place frame set A on the left and right...
- Page 19 PLASMA DISPLAY HANGER UNIT INSTALLING WALL FRAME SET B AND CONNECTING FRAME INSTALLING WALL FRAME SET B AND CONNECTING FRAME. Frame set B Place frame set B on the left and right side of Connecting Frame the unit and use the enclosed screws (M5) to secure them tightly.
- Page 20 INSTALL THE WALL FRAME SET ON THE WALL Install the wall frame set on the wall by matching the concrete anchors with the holes, then use the wall screws (8) to secure tightly. INSTALLING ON THE WALL HELD BY SUPPORTING WOODEN STRUCTURE If it is not feasible to attach frame set B firmly and completely, due to the distance between the two supporting woods;...
- Page 21 PLASMA DISPLAY HANGER UNIT INSTALLING PLASMA DISPLAY ON THE WALL CONNECTING UPPER PART OF FRAME SET A AND FRAME SET B Insert the upper part of frame set A (X) to frame set B (Y) as indicated below. Frame set B Frame set A At least two people are needed to put these frames together.
- Page 22 TO PROVIDE THE SECUREST FIT After installing plasma display and wall frame sets, for a more secure fit, secure M5 screws (M5x30) on the (Z) part so that (Z) will not move up and down as shown in the picture below.
- Page 23 PLASMA DISPLAY HANGER UNIT 4. ADJUSTING ANGLES AFTER INSTALLATION (10˚, 15˚, 20˚) HOW TO ADJUST VIEWING ANGLES Take out the screws from the upper part of the frame. Insert the upper part of the frame set B angle adjustment lever to its gap.
- Page 24 PLASMA MONITOR (DISPLAY) STAND Thank you for purchasing the Gold vision Plasma Monitor stand. This stand is specifically designed only for the Gold vision Plasma Display. To ensure the safe operation of the unit, please read these instructions before installing.
- Page 25 TABLE OF CONTENTS 1. Check for enclosed parts ......1 2. Important Safety Instructions ...... 2 3. Assembly Instructions ......... 3 4. Disassembling Instructions ......5 1. PLEASE CHECK FOR THE ITEMS SHOWN BELOW STAND M5 SCREWS...
- Page 26 PLASMA DISPLAY STAND 2. IMPORTANT SAFETY INSTRUCTIONS PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT. WARNING : Disregarding these instructions can result in serious injury. WARNING CAUTION : Disregarding these instructions will result in the CAUTION mistreatment of the unit and can result in injury or damage to the unit.
- Page 27 3. ASSEMBLING INSTRUCTIONS HOW TO DISPOSE OF THE PLASMA MONITOR WRAPPER First dispose of the wrapping band and Afterwards, dispose of the Styrofoam raise the top box to open. and remove the vinyl covering.
- Page 28 PLASMA DISPLAY STAND ASSEMBLING THE PLASMA DISPLAY STAND Slide the stand under the plasma display Open and take out the stand from the like the picture below. box and remove wrapper. Use the enclosed 4 M5 screws to secure the assembled stand. M5 Screws (Picture of a properly installed stand and display)
-
Page 29: Disassembling Instructions
4. DISASSEMBLING INSTRUCTIONS DISASSEMBLING PLASMA DISPLAY STAND Place a protective covering over the Completely unscrew the secured 4 surface you will be working on and lay the screws. plasma display as shown below. Pull the stand away from the plasma display to disassemble.