Table of Contents
Advertisement
Available languages
Available languages
Quick Links
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Clearances and Dimensions
1. Provide adequate clearances between the range and adjacent combustible surfaces.
2. Location—Check location where the range will be installed. Check for proper electrical supply, and the stability of the
floor.
3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid
and level.
Fig. 1
*30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM OF AN UNPROTECTED WOOD OR METAL
CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT
MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM OR 0.020" COPPER.
0" CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO
PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS.
TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED
ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY
INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.
IMPORTANT SAFETY INSTRUCTIONS
If the information in this manual is not followed
exactly, a fire or electrical shock may result causing property
damage, personal injury or death.
Important Notes to the Installer
•
Read all instructions contained in these installation instructions
before installing range.
•
Remove all packing material from the oven compartments
before connecting the gas & electrical supply to the range.
•
Observe all governing codes and ordinances.
•
Be sure to leave these instructions with the consumer.
p/n 316454905 (0703) EN
(For 3 or 4 Wire, 60 Hz. Systems)
Fig. 2
Fig. 3
Important Note to the Consumer
Keep these instructions with your owner's guide for future
reference.
•
As when using any appliance generating heat, there are
certain safety precautions you should follow. These are
listed in the Use & Care Manual, read it carefully.
•
Be sure your range is installed and grounded properly by
a qualified installer or service technician.
•
Make sure the wall coverings around the range can
withstand the heat generated by the range.
•
To eliminate the need to reach over the surface elements,
cabinet storage space above the elements should be
avoided.
Serial Plate Locations:
Serial plate is located on the lower right front frame of the appliance.
Alternate location may be under cooktop.
1
30"
Español - Páginas 5-8
Advertisement
Table of Contents
Related Manuals for Frigidaire 316454905
Summary of Contents for Frigidaire 316454905
- Page 1 Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces. 2. Location—Check location where the range will be installed. Check for proper electrical supply, and the stability of the floor. 3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level.
-
Page 2: Before Starting
Anti-Tip Bracket and screws packed with the range. Failure to install the anti-tip bracket will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself. -
Page 3: Power Cord Connections
3 & 4 - Wire electrical wall Receptacle types & Fig. 8 NOTE: Range is shipped from factory with 1-3/8" dia. hole as shown. To use either 7/8" dia. hole or 1-1/8" dia. knockouts refer to Fig. 9. - Page 4 (See Fig. 9). Grounding Instructions (3-Wire Connections only): strap is installed on this range which connects the center terminal of the terminal block (Neutral) to the range chassis. The ground strap is connected to the range by the center, lowest screw (See Fig. 13). The ground strap must not be removed unless National, State or Local Codes do not permit use of a ground strap.
-
Page 5: Instrucciones Importantes De Seguridad
• Observe todos los códigos y reglamentos vigentes. • Asegúrese de dejar estas instrucciones con el usuario. p/n 316454905 (0703) SP (Para sistemas trifilares o tetrafilares de 60 Hz) Fig. 2 Fig. 3 Aviso importante al consumidor Mantenga estas instrucciones con su Guía de Uso y Cuidado para... -
Page 6: Antes De Comenzar
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" ANTES DE COMENZAR Herramientas Necesarias Para los tornillos niveladores y soporte antivuelco: • Llave ajustable o pinzas ajustables • Llave de tuerca de 5/16" o destornillador de punta plana • Taladro eléctrico y broca de 1/8" de diám. (broca para taladro de mampostería si está... - Page 7 INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" Consulte la Tabla del Tamaño de la Abertura de Conexión de la Estufa (Figs. 9 y 10) para la información sobre los amperes del juego de cordón. Los bornes en los extremos de los almabres deben ser de anillo cerrado u horquillas abiertas con extremos dirigidos hacia arriba.
- Page 8 INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" o 4B. CONEXIONES DEL CORDON DE ALIMENTACION Instrucciones para conexión trifilar (para instalaciones existentes SOLAMENTE - Consulte la Fig. 13). Siga las instrucciones de instalación del fabricante suministradas con el sujetacable e instale (Además vea las Figs.