Table of Contents
Advertisement
V-027X User Guide
7/9/06
15:04
Page 16
UK
0QH,
recycle
product
VAX Model Number: V-027x
I n s t r u c t i o n M a n u a l
Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK. For your nearest Service Agent please call VAX Care.
www.vax.co.uk
WR9
Worcestershire
Droitwich,
advice.
recycling
for
retailer
or
Authority
Please
waste.
household
with
93/68/EEC
by
modified
as
Directive
93/68/EEC
by
modified
following:
the
with
compliance
the
that
declare
responsibility
own
COMPLIANCE
website:
-
info@vax.co.uk
email:
Lovett,
Hampton
Road,
Local
your
with
Check
exist.
of
disposed
be
not
should
products
compatibility
Electromagnetic
89/336/EEC
as
Directive
Voltage
Low
73/23/EEC
in
manufactured
is
Ultra
Rapide
our
on
hereby
Limited,
VAX
importer:
OF
STATEMENT
EEC
Please read carefully before using the carpet washer.
Always fully extend the mains cable before use.
Please retain these instructions for future reference.
Kingswood
Ltd.,
Vax
facilities
where
electrical
Waste
EMC:
Safety:
V-027x
Manufacturer/EEC
VAX CARELINE 0870 6061248
Easy Guide
Advertisement
Table of Contents
Related Manuals for Vax Rapide XL Ultra V-027X
Summary of Contents for Vax Rapide XL Ultra V-027X
- Page 1 Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate. Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK. For your nearest Service Agent please call VAX Care.
-
Page 2: Parts Checklist
V-027X User Guide 7/9/06 15:04 Page 1 Parts checklist Handle Front suction nozzle Quick cord release aa Carrying handle Solution trigger Dirty water tank bb Clean water tank cap Brush on/off Floor/tools selector cc Hose storage clips Soap on/off Hose attachment cover... -
Page 3: Clean Water Tank
V-027X User Guide 7/9/06 15:04 Page 2 Putting your cleaner together Feed the cord through the slots on Place a nut into the recess in the Remove the backing tape from the the back of the handle and push back of the upper handle. While screw cover and press into place. - Page 4 V-027X User Guide 7/9/06 15:04 Page 3 Tool storage Slide the tool caddy downwards Connect upholstery attachment to Push upholstery attachment into until it is secured in place. end of hose by pressing until it the left hose clip, wrap the hose clicks into place.
- Page 5 V-027X User Guide 7/9/06 15:04 Page 4 Pre-treating your carpets with the pre-treatment wand and solution Remove solution tank cap. CAUTION: Do not overfill. You should leave Replace the solution tank cap. 1-2 cm of air space. Return the solution tank to the cleaner making sure the solution Fill the tank with pre-treatment solution.
- Page 6 Tipping the cleaner and breaking the seal of the nozzle against the carpet will cause the float to rise cutting off suction. Once the float is activated, empty the dirty water tank. If the tank does not appear full turn off the power switch and wait for the float to settle. For best results use only VAX AAA Carpet Cleaner.
-
Page 7: How To Operate Your Cleaner
1-2 cm of air space. Return the solution tank to the cleaner making sure the solution Fill the tank with VAX AAA Carpet Cleaner. tube lines up with the groove in the The cleaner can be stored with solution in the back of the solution tank. - Page 8 V-027X User Guide 7/9/06 15:04 Page 7 How to operate your cleaner To spray cleaning solution, depress Plug the cord into an electrical Turn main power switch, brush the solution release trigger (3a) and socket. Step on the handle release...
-
Page 9: Hose Attachments
V-027X User Guide 7/9/06 15:04 Page 8 Hose attachments Put the cleaner in its upright Remove the hose from its stored Insert the end of the hose into the position. Turn the brush switch and position on the back of the cleaner. - Page 10 V-027X User Guide 7/9/06 15:04 Page 9 Hose attachments While depressing the blue solution spray Remove the hose from the fitting by Disconnect water supply connector trigger, pull the attachment in a downward twisting it counterclockwise to from the water supply port by motion.
-
Page 11: Emptying The Dirty Water Tank
V-027X User Guide 7/9/06 15:04 Page 10 Battery Compartment 2 Hose Release Button Power Button Oscillating Brushes Battery Compartment 1 Now attach the Power Wash Brush To rinse, remember to turn the soap Insert the four AA batteries into to the hose attachment by pushing... - Page 12 V-027X User Guide 7/9/06 15:04 Page 11 Dirty water tank can be rinsed out Return the dirty water tank cap. Lift the dirty water tank handle and with hot tap water to remove any pull out the filter to clean. Rinse remaining debris.
- Page 13 V-027X User Guide 7/9/06 15:04 Page 12 Belt or brush removal Phillips screwdriver required and replacement Remove dirty water tank and front Use a Phillips screwdriver to Remove the belt cover. Remove the nozzle (see page 20) put them to remove two (2) screws.
-
Page 14: Troubleshooting
• Clean pick up tube by soaking in water No soap dispensing • No soap. • Fill soap tank with Vax AAA Carpet Cleaner. • Turn soap switch on. • Soap switch off. • Fill soap tank or shut soap power OFF. - Page 15 • A hazard may occur if the appliance runs over the power supply cord. • Carpets should be dry vacuumed thoroughly before washing with the Rapide XL and Rapide XL Pro. For further information in the UK, call the VAX HELPLINE : 0870 606 1248...