Audioplex AT-880S Installation Manual

Maximum Power Handling:
Freq. Response:
Impedance:
Overall Dimensions:
Cut Out Dimensions:
Speaker:
Connectors:
The AT-880S subwoofer speaker assemblies are designed for flush installation in walls where conventional box speakers
are not desirable. These speakers can be installed in either new or existing construction.
It is important when installing your speakers and/or running wire through your house or office, that you check any local
codes and requirements to make sure that safety is being observed. We suggest that where necessary a professional be consulted
in order to optimize your system's performance. The following, however, are just a few of the do's and don'ts:
Follow the wiring diagram on the back of this page. Carefully map out the wiring path from the amplifier to the AT-880S
and from the AT-880S to the main speakers. We recommend a minimum of 16 gauge wire for this installation. Be sure that the
speaker wire does not rest or rub against any sharp or pointed objects. The speaker should be mounted on a flat surface to form a
good seal between the speaker flange and the mounting surface. To help tune the AT-880S to your room, we have incorporated
two sets of switches. The switches on the front of the speaker labeled Normal and Reverse, are for switching the speaker in and
out of phase. Sometimes conflicts can occur between the Subwoofer and the satellite speakers that can easily be remedied by
reversing the phase of the subwoofer. The best way to determine the setting for your environment is to listen from the intended
seating area while an assistant changes the switch settings (both switches should be in either normal or reverse position). The
switches on the back of the AT-880S are designed to match the cross-over point on our AT-502 and AT-602 speaker series. For
more information, see text above the wiring diagram on the back side of this sheet.
1. Use cut-out template to mark and cut hole for each speaker.
2. Run speaker wire from amplifier to the speaker cut-out and to main speakers.
3. Remove grill cover from the speaker to gain access to the mounting holes.
4. Connect wires from the amplifier to the subwoofer and from the subwoofer to
the main speakers (carefuly observing polarity!)
5. Carefully start threading the mounting screws through the speaker into the mounting arms.
6. Position speaker in the cut-out.
7. Carefully tighten mounting screws, and snap speaker grill back into place.
Your AUDIOPLEX TECHNOLOGY AT-880S subwoofer is covered by a 5 year warranty against any defects in
workmanship and materials. Any defects will be remedied without charge for labor and parts.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this warranty.
AUDIOPLEX TECHNOLOGY is not responsible for defective operation caused by abuse or by modification or service by any
unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply. Any necessary
servicing must be done by AUDIOPLEX TECHNOLOGY. The product must be returned expenses prepaid, with written
authorization from the company. The product must be shipped with the proof of purchase and in the original carton and packing
material to avoid damage.
This warranty gives you specific legal rights. You may have other rights which vary from state to state.
404 GWH
1-800-257-2077
INSTALLATION MANUAL
TECHNOLOGY
AT-880S IN-WALL SUBWOOFER
SPECIFICATIONS
250 Watts Continuous
38Hz-300Hz Sub Ouput / 300Hz - 20KHz Satellite / Monitor Outputs
8 Ohms
10-1/8" x 14-1/8"
8-3/4" x 12-3/4"
8" Textured, Injection Molded Polypropylene
Spring Clips
INSTALLATION
WARRANTY
AUDIOPLEX TECHNOLOGY
P.O. BOX 440
603-544-8601
www.audioplex.com
MELVIN VILLAGE, N.H. 03850
FAX: 603-544-8901
WARNING!
Over-tightening brackets will
crack rim of speaker
Do not use power tools
to tighten bracket
Hand-tighten only
2003 - 9/2/03