Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Sunforce Manuals
  4. Security Camera
  5. MOTION ACTIVATED SECURITY LIGHT & VIDEO...
  6. Manual

Sunforce MOTION ACTIVATED SECURITY LIGHT & VIDEO CAMERA Manual

Motion activated security light & video camera
Hide thumbs

Advertisement

Quick Links

Download this manual
Enlarged version
MOTION ACTIVATED SECURITY LIGHT & VIDEO CAMERA
Front View
Side View
Front Surround
Lampshade
Microphone
Camera
PIR (Motion Sensor)
Warning Speaker
Lux Control Knob
Time Control Knob (PIR trigger time)
LCD control panel and Setting buttons
Battery Cover
SD Card Slot
PACKAGE CONTENT
The Motion Activated Security Light & Video Camera is
packed specially to minimize the chance of the
6
7
8
Rear View
contents been damaged during shipping and handling.
Please check the unit carefully and confirm the
contents listed below are included.
No.
1
Base Unit (VC603)
2
AA Size 1.5V Alkaline Battery
3
2GB SD Card
4
Screw Pack
5
Halogen Bulb
6
Operating Instruction Manual
INTRODUCTION
9
Your MOTION ACTIVATED SECURITY LIGHT &
VIDEO CAMERA is a unique surveillance system for
your home or business. At night, the built-in passive
infrared (PIR) motion sensor turns on the light when it
detects motion in its coverage area, so that camera
images can be clearly seen.
built-in
photocell
deactivating the light. Built-in SD card slot for additional
storage, accept memory storage up to 32GB.
Pre-recorded function allows you to trace event
happening, and customized sound recording is
available at your disposal.
The MOTION ACTIVATED SECURITY LIGHT & VIDEO
CAMERA is compatible with O-Net product and can be
controlled by remote controller. The unit is designed
for indoor/outdoor use.
Note: Read this entire manual before you start to install
the system.
BEFORE START
Please follow the steps as suggested below to get a
better result of installation.
CAUTION: 4 batteries provide for function setting
only, NOT installing the battery until you're ready to set
the function and mount on the wall, the battery power
supports for about 1 hour operation after installed.
POWER UP
The Motion Activated Security Light & Video Camera is
powered by batteries at the initial stage. Press and
release the battery cover, insert 4 AA size 1.5V alkaline
batteries to the battery spring. Please ensure correct
polarity is put.
(FIGURE 1)
1
Item
During the day, the
sensor
saves
electricity
After that, refit the battery cover.
FIGURE 1
Qty
1
4
1
1
1
1
by

Advertisement

loading
Need help?

Need help?

Do you have a question about the MOTION ACTIVATED SECURITY LIGHT & VIDEO CAMERA and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Sunforce MOTION ACTIVATED SECURITY LIGHT & VIDEO CAMERA

Summary of Contents for Sunforce MOTION ACTIVATED SECURITY LIGHT & VIDEO CAMERA

  • Page 1 contents been damaged during shipping and handling. Please check the unit carefully and confirm the contents listed below are included. Item MOTION ACTIVATED SECURITY LIGHT & VIDEO CAMERA Base Unit (VC603) AA Size 1.5V Alkaline Battery 2GB SD Card Screw Pack Front View Halogen Bulb Operating Instruction Manual...
  • Page 2 (2) Insert SD card into the card slot (FIGURE 5). Once Motion Activated Security Light & Video Camera is powered up, it enters PIR warm up time. The LCD displays as below (FIGURE 2). FIGURE 5 FIGURE 2 (3) Refit the cover, and fasten the screw clockwise After 3 seconds, the unit enters standby mode (as (FIGURE 6).
  • Page 3 detects a motion; it can be varied from 4 to 12 seconds. During this time, video will be taken which allows you to (4) Take off the front surround. Install bulb by inserting trace what’s happening. To ensure you get correct one end first and depressing until enough time and day for the recorded images, it is particular clearance is gained to seat the other end of the...
  • Page 4 Note: If no action is taken within 12 seconds, the LCD returns back to standby mode; the setting is not saved. To ensure the setting has been saved properly, always keep pressing Set until LCD returns back to Standby Mode. GENERAL SETTING FIGURE 16 1.

  • Page 5: Figure

    FIGURE 19 FIGURE 23 Warning sound 1 is the preset sound. Five warning Built-in microphone is used for video recording and for sounds are available for selecting, while warning sound creating your unique warning sound. To create your 3 and 4 are opened for your voice/sound recording. The unique sound (warning sound 3 &...

  • Page 6: Figure

    Press Set, the light is still on, reminds user the Motion failed and LCD returns back to standby mode. If ID code learning is successful, LCD returns back to Activated Security Light & Video Camera starts operating. Four PIR sensitivities are available for standby mode and PIR stops detecting function for one minute.

  • Page 7: Figure

    light starts operating. Provisionally turn the LUX control knob to the edge at the moon (dusk) position (FIGURE 31). In this provisional setting mode, the Motion Sensor remains inactive during daylight. At dusk when you find it is the LUX level desired for operation, simply set the LUX control knob to the position which will become active as daylight declines.

  • Page 8: Rubber Bumper Around The Square Protrusion Of Clamp. (Figure

    Note: THIS EQUIPMENT MUST NOT BE MOUNTED ON AN OUTLET BOX WHICH IS SUPPORTED BY A BAR HANGER or equivalent (NE PAS MONTER CET ÉQUIPEMENT SUR UNE BOÎTE DE SORTIE FIXÉE À UNE BARRE DE SUSPENSION or equivalent). Japanese Version According to the place where you plan to install, choose whichever suits you most.

  • Page 9: Table Of Contents

    FIGURE 44 FIGURE 41 (2) Insert the L shaped holder through the two holes on (2) Insert the pole band through the two holes on the the clamp. (FIGURE 42) clamp. (FIGURE 45) FIGURE 42 FIGURE 45 (3) Using the thumb nut on the L shaped holder, fasten (3) Measure the required length of pole band to be the unit on the pillar.

  • Page 10: Figure

    FIGURE 51 FIGURE 48 (8) The unit should be earthed. Note: There is a “UP” mark shown on the interior Make sure that the terminal block is put in its wall box. Be sure to have “UP” mark shown original position after connecting the wires. upwardly when fixing the wall box on the wall.
  • Page 11 guarantee that interference will not occur in a particular SPECIFICATIONS installation. If this equipment does cause harmful 120V~ 60Hz for USA or interference to radio or television reception, which can be 220-240V~ 50Hz for EU or determined by turning the equipment off and on, the user is Power Requirement 1.5V AA alkaline battery x 4 encouraged to try to correct the interference by one of the...