Table of Contents
Advertisement
Quick Links
Part Number
：H7110SG100
Description
：Forester AC 110V Power Outlet
1. PRE INSTALLATION / INSTALLATION OVERVIEW
2. KIT CONTENTS
INSTALLATION INSTRUCTIONS
Fuji Heavy Industries Ltd.
AC 110V POWER OUTLET
No.
OUTLET
BRACKET
RUBBER GASKET
TAPPING SCREW
INVERTER
BRACKET
SCREW (M4)
HARNESS
DOUBLE SIDED TAPE
ALUMINUM TAPE
FOAM TAPE
TIE WRAP (150mm )
OWNERS MANUAL
OUTLET KIT
INVERTER
HARNESS
1
Part Name
H7110AJ110
, , ,
H7110AJ130
H7110AJ120
Rev 1.0
Q'ty
1
1
1
2
1
2
4
1
1
2
1
3
1
Advertisement
Table of Contents
Summary of Contents for Subaru Forester AC 110V Power Outlet
- Page 1 AC 110V POWER OUTLET INSTALLATION INSTRUCTIONS Part Number ：H7110SG100 Description ：Forester AC 110V Power Outlet 1. PRE INSTALLATION / INSTALLATION OVERVIEW 2. KIT CONTENTS Part Name Q'ty OUTLET BRACKET RUBBER GASKET TAPPING SCREW INVERTER BRACKET SCREW (M4) HARNESS DOUBLE SIDED TAPE...
-
Page 2: Tools Required
Occupant Detection System may not operate as designed which may result in injuries to the front seat passenger. Therefore, it is strongly recommended that the product be installed at an authorized Subaru dealer. Please follow the Instructions for your safety. - Page 3 5. INSTALLATION PROCEDURE 1. REMOVAL OF INTERIOR TRIM COMPONENTS Passengers Seat Removal: 1. Remove four seat rail bolts. When removing Seat rail bolt (Qty 4) left rear rail bolt cover, remove only the lower section by following the instructions in the illustration below.
- Page 4 Remove the following components: arking brake lever onsole (RH/LH) hift lever onsole box onsole cover : Clip Screw Bolts (10mm) : Clip Clip Slide the armrest Clip : Bolt...
- Page 5 2. TRIM FLOOR CARPET (Passenger side,under seat area) 1. Apply masking tape to the floor carpet in the areas shown in the image on the left. FRONT 2. Cut out the floor carpet around the outside edge of the masking tape. CAUTION When cutting out the floor carpet, take care that you do not cut the vehicle harness.
- Page 6 4. CONNECT HARNESS TO VEHICLE HARNESS 1. After disconnecting vehicle harness from Black 12V Power outlet, insert red spade terminal Terminal (Black) into white wire side of vehicle connector as shown. Insert black spade terminal into black wire side of vehicle connector as shown. White Vehicle Power-socket connector Terminal (Red)
-
Page 7: Wire Harness Installation
5. WIRE HARNESS INSTALLATION 1. Lay the wiring harness alongside vehicle harness as shown in the image. 2. Feed the unit connector of wiring harness from the console box under the floor carpet, and pull it out of the cutout in the carpet as shown in the image. - Page 8 6. CONSOLE OUTLET MOUNTING HOLE PROCESSING 1. Mark the scribed area on the center console back panel with the tip of a hole punch. 2. Drill three φ3.5mm (1/8") holes and then enlarge center hole φ24mm (15/16") with hole saw. CAUTION 24mm Wrap fabric adhesion tape...
- Page 9 7. OUTLET INSTALLATION 1. Fit Rubber gasket onto Outlet Console cover position Holes Outlet over holes drilled from the above step. 2. Place Bracket on the other side of the center console and mount the Outlet with Bracket the two supplied self apping screws Rubber gasket Outlet Self-tapping screws...
-
Page 10: Check The Operation
8. CHECK THE OPERATION CAUTION 1. POST-INSTALLATION CHECK 1. Check that all wiring and attaching points are correct. 2. Be careful not to pinch, strain, or crush wires during reassembly. 3. Be careful not to damage vehicle parts during reassembly. 2. -
Page 11: Troubleshooting
9. TROUBLESHOOTING This section describes the inspection procedure for malfunction which may take place after installation is completed. Use a circuit tester for continuity and/or voltage testing. Checking Procedure A Checking connectors of the main body Check the continuity and/or voltage of connector terminals connected to the main body (with all other connectors still connected). -
Page 12: Circuit Diagram
10. RE-ASSEMBLY After the check procedure is completed, re-assemble all removed vehicle parts and components paying attention not to damage them. CAUTION 1. Be careful to avoid pinching the harness or any vehicle harness , or damaging any vehicle parts when reassembling parts and/or components.