Related Manuals for TerraTec digitalXtension microWAVE PC
Summary of Contents for TerraTec digitalXtension microWAVE PC
- Page 2 † † † †...
- Page 7 ¼ ¼...
- Page 10 microWAVE PC.ttm default.mws...
- Page 11 .DRV .VXD...
- Page 12 ¼...
- Page 13 a:\setup microWAVE PC.ttm...
- Page 26 >> <<...
- Page 28 > >...
- Page 38 So follwing valid IDM exist: Label Value Description Waldorf Microwave 2 System Exclusive Specifications, -------------------------------------------------- Software release 2.09 SNDR Sound Request SNDD Sound Dump 1. General SNDP Sound Parameter Change *************************************************** MULR Multi Request Sys-Ex dumps and requests will always be in the MULD Multi Dump following form:...
- Page 39 ------------------------------------------------ Or in case of All Sounds Dump: Index Label Value Description Index Label Value Description --------------------------------------------------- ------------------------------------------------ Marks Start of SysEx Marks Start of SysEx Waldorf Electronics Waldorf Electronics GmbH ID GmbH ID Microwave 2 ID Microwave 2 ID Device ID Device ID here MULR (Multi...
- Page 40 The actual Format is: 2.41 WCTR *************************************************** Index Label Value Description WCTR Wave Control Table Request ----------------------- --------------------------- Marks Start of SysEx Upon reception of a valid wave control table request, Waldorf Electronics the MW2 will dump the selected Table. The location is GmbH ID given in two bytes with following conventions: Microwave 2 ID...
- Page 41 2.51 GLBR 2.61 DISR *************************************************** *************************************************** WCTR Global Parameter Request DISR Display Request Upon reception of a valid Global Parameter request, Upon reception of a valid Display Request request, the the MW2 will dump the Global Parameters. No location MW2 will dump the contents of the LCD. No location is is given.
- Page 42 2.64 DISL 2.81 MODR *************************************************** *************************************************** DISL LCD Recall MODR Mode Request Upon receprion of a Display Recall message, the LCD and the LEDs will be updated in order to discard a The full format of a MODR Dump is: possibly previously dumped LCD content.
- Page 43 3. Data Formats 3.1 SDATA - Sound Data ***************************************************************************** Note: All Parameters marked as "reserved" should be set to 0 for future compatibility. Index Range Value Parameter ---------------------------------------------------------------------------------- Sound Format Version, currently 1, Format 0 is unpublished 16-112 -4...+4 Osc 1 Octave in Steps of 12 52-76 -12..+12 Osc 1 Semitone...
- Page 44 0-127 Effect Parameter #1 !! off/on Chorus !! 0-127 Effect Parameter #2 !! 0-127 left 64-center-right 63 Panning 0-127 -200%..+197% Panning Keytrack 0-127 Effect Parameter #3 !! off/on Glide Active porta,gliss,fp.,fg. Glide Type exp./linear Glide Mode 0-127 0..127 Glide Time reserved off,on,hold Arpeggiator Active...
- Page 45 0-127 -64..+63 LFO 2 Symmetry 0-127 0..127 LFO 2 Humanize 0-127 free,3-357 degree LFO 2 Phase reserved 0-31 see List 3.12 Modifier Delay Source 0-127 0..127 Modifier Delay Time 0-31 see List 3.12 Modifier 1 Source 1 0-31 see List 3.12 Modifier 1 Source 2 0-15 see List 3.14...
- Page 46 3.11 Play Parameters 3.12 Modulation Sources *************************************************** *************************************************** Value Index Parameter --------------------------------------------------- Index Modulation Source Osc 1 Octave --------------------------------------------------- Osc 1 Semitone Osc 1 Detune LFO1 Osc 1 Pitchbend LFO1 * Modwheel Osc 1 Keytrack LFO1 * Aftertouch Osc 2 Octave LFO2 Osc 2 Semitone Filter Envelope...
- Page 47 3.14 Modifiers ***************************************************************************** Index Operand Operation ----------------------------------------------------------------------------- Addition Subtraction Multiplication Division Bitwise exclusive-or Bitwise inclusive-or Bitwise and S&H Sample & Hold Ramp Switch Abs value Min value Max value Lag processor Control filter Differentiator ----------------------------------------------------------------------------- ***************************************************************************** 3.15 Filter 1 Types ***************************************************************************** Index Filter Type...
- Page 48 3.3 IDATA - Instrument Data ***************************************************************************** Index Range Value Parameter ----------------------------------------------------------------------------- Sound Bank 0-127 1..128 Sound Number 0-17 global,omni,1-16 MIDI Channel 0-127 0..127 Volume 16-112 -48..+48 Transpose 0-127 -64..+63 Detune Main Out/Sub Out Output off/on Status 0-127 left64..center..right63 Panning off/on/inverse Pan Mod reserved reserved...
- Page 49 Device family member code, see below VV,VV,VV,VV, Software revision, ASCII, e.g. "2.09" Device family member codes (XX,YY): 00,00 Microwave 2 01,00 Microwave 2 with XT Mainboard (has Delay Effects !) 03,00 Microwave XT 05,00 Microwave PC on Terratec EWS Frontmodule *****************************************************************************...
- Page 50 2.82 INFR ******************************************************************** INFR Information Request This only works for Microwave PC on Terratec EWS Frontmodule ! The full format of a INFR Dump is: Index Label Value Description ----------------------------------------------------------- Marks Start of SysEx Waldorf Electronics GmbH ID Microwave 2 ID...
Need help?
Do you have a question about the digitalXtension microWAVE PC and is the answer not in the manual?
Questions and answers