Power Supply - American DJ LED Trispot User Instructions

LED Trispot
ower Supply:
P Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ
LED Trispot. The American DJ
Because of voltage setup of the unit you do not have to worry about
wall output voltage. This unit is compatiable with all wall outputs.
DMX-512:
DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that trav-
els from fixture to fixture via the DATA "IN" and DATA "OUT" XLR ter-
minals located on all DMX fixtures (most controllers only have a DATA
"OUT" terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compli-
ant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Dip-switches in DMX mode: This unit uses dip switches to assign a
DMX address. Each dip switch represents a binary value.
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
Dipswitch 10 - Some units omit dipswitch 10. When a unit does in-
clude dipswitch 10 it is usually used for special functions such as
sound activation.
©American DJ® - www.americandj.com - LED Trispot Instruction Manual Page 5
LED Trispot is a 100v ~ 220v unit.
®
DMX CHANNEL
2 8 32
ON
1 2 3 4 5 6 7
1 4 16 65
Set Up LED Trispot
Each dip switch has a preset value. A specific DMX address is set by
combining the dip switches that sum your desired value. For example:
®
To achieve a DMX address of 21, combine dip switches 1, 3, and 5.
Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4, and
dip switch 5 has a value of 16, the combination of the create a DMX
value of 21.
Set DMX address 21:
Dip-switches #
Data Cable (DMX Cable) Requirements (For DMX Operation):
The LED Trispot can be controlled via DMX-512 protocol. The LED Tri-
spot can be either a three or five channel DMX unit. The DMX address
is set on the back panel of the LED Trispot. Your unit and your DMX
controller require a standard 3-pin XLR connector
for data input and data output (Figure 1). If you are
making your own cables, be sure to use standard
two conductor shielded cable (This cable may be
SOUND
purchased at almost all pro sound and lighting
stores). Your cables should be made with a male
and female XLR connector on either end of the
cable. Also remember that DMX cable must be
daisy chained and can not be split.
Notice:
Be sure to follow figures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
128 SF
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
8 9 10
256
American DJ Supply
©
Set DMX address 201:
1 = 1 Dip-switches #
3 = 4
5 = 16
= 21
REMOTE
INPUT OUTPUT
CONTROL SOUND
INPUT
POWER
DMX512
DMX+,DMX-,COMMON
COMMON
DMX +
1
DMX512 OUT
3 3
3-PIN XLR
DMX -
2
- www.americandj.com - LED Trispot Instruction Manual Page 6
®
Set Up
1 = 1
4 = 8
7 = 64
8 = 128
= 201
REMOTE
INPUT OUTPUT
CONTROL
INPUT
Figure 1
POWER
Termination reduce
avoids signal trans
1 1
DMX512 IN
and interference. It
3
3-PIN XLR
to connect a DMX te
2 2
120 Ohm 1/4 W) bet
Figure 2
and PIN 3 (DMX +)
SOUND