Related Manuals for Mitsubishi Electric MDT52IS
Summary of Contents for Mitsubishi Electric MDT52IS
- Page 1 52" LCD Display Monitor USER’S MANUAL BEDIENERHANDBUCH MANUAL DEL USUARIO MANUEL UTILISATEUR MANUALE UTENTE GEBRUIKERSHANDLEIDING...
-
Page 2: Table Of Contents
Index Important Information ........................... English-2 Safety Precautions, Maintenance & Recommended Use ................English-4 Contents ............................... English-5 Parts Name and Functions .......................... English-6 Buttons, Switch, and Indicator ....................... English-6 Connectors and Terminals ......................English-7 Wireless Remote Control ....................... English-8 < Operating Range for the Remote Control > ................English-9 <... -
Page 3: Important Information
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: Mitsubishi Digital Electronics America, Inc. Address: 9351 Jeronimo Road, Irvine, California 92618 U.S.A. -
Page 4: English
This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV, and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II. Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. -
Page 5: Safety Precautions, Maintenance & Recommended Use
Safety Precautions, Maintenance & Recommended Use FOR OPTIMUM PERFORMANCE, PLEASE NOTE • The power cable connector is the primary means of THE FOLLOWING WHEN SETTING UP AND USING detaching the system from the power supply. The monitor THE LCD COLOR MONITOR: should be installed close to a power outlet, which is easily accessible. -
Page 6: Contents
Contents Your new MDT521S monitor box* should contain the following: • LCD monitor • Screw for Clamper (To prevent from falling) x 2 • Power Cord (3 m) • CAT5 Tx BOX • Video Signal Cable (4 m) • CD-ROM •... -
Page 7: Parts Name And Functions
Parts Name and Functions Buttons, Switch, and Indicator Remote control sensor and Power indicator UP ( ) button Receives the signal from the remote control (when using the Activates the OSD menu when the OSD menu is turned-off. wireless remote control). See also page 9. Acts as button to move the highlighted area up to select Glows green when the LCD monitor is in active and glows... -
Page 8: Connectors And Terminals
Connectors and Terminals (OUT) (IN) (OUT) (IN) (OUT) (IN) (IN) (IN) CAT5 input/output connectors (RJ-45) EXTERNAL SPEAKER TERMINAL The IN (RGB5 IN) connector is for connecting the CAT5 To output the audio signal for external speakers from AUDIO 1, Tx BOX or the CAT5 OUT connector of a multi-connected 2, 3 jack or HDMI. -
Page 9: Wireless Remote Control
Wireless Remote Control AUDIO INPUT button Press to change the audio source for each video source. The audio source is changed from [AUDIO1] to [AUDIO2], [AUDIO3] and [HDMI] in order. Note that you cannot select the audio source for [VIDEO<S>] or [VIDEO]. [HDMI] is selectable only when the video source is [RGB 1] and [RGB 2]. -
Page 10: Operating Range For The Remote Control
CAT5 Tx BOX < Operating Range for the Remote Control > Point the top of the remote control toward the LCD monitor's remote sensor during button operation. Use the remote control within a distance of about 7 m/23 ft. from the front of the LCD monitor's remote control sensor USB (B type) and at a horizontal and vertical angle of within 30°... -
Page 11: Setup Procedure
Setup Procedure 1. Determine the installation location • Place “AAA” batteries matching the + and - signs on each battery to the + and - signs of the battery compartment. CAUTION: • Do not mix battery types. DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY •... -
Page 12: English
6. Operate the attached external equipment How to install the stands 1. Please turn monitor off. Display the signal on the external equipment you wish. 2. Fasten screws on both sides of the monitor. NOTE: 7. Adjust the sound Install the stands so that their longer portions come to the Make adjustments lowering or rising the volume as required. -
Page 13: Cat5 Video Connection
13. When MDT521S is installed in portrait CAT5 video connection position The CAT5 video connection function is for transmitting the Conditions analog RGB video signal of the computer and the control MDT521S can be installed in portrait position, under the fol- signal of the monitor over a long distance using CAT5 cables. -
Page 14: English
2) CAT5 EQ 2. Connect the D-SUB input connector of the CAT5 Tx BOX and the VGA (D-SUB) output connector of the computer Make adjustment so that blur and smear of the displayed let- using the signal cable (mini D-SUB 15-pin cable) supplied ters and graphic objects are minimized. -
Page 15: How To Mount And Attach Options To The Lcd Monitor
Prevent the screws from loosening using spring washers, When you use screw hooks (commercially available), ring etc. MITSUBISHI ELECTRIC recommends using mounting screw hooks, not C-shaped screw hooks (with opening), are interface that comply with TÜV-GS and/or UL1678 standard recommended. -
Page 16: Connections
Connections Before making connections: First turn off the power of all the attached equipment and make connections. Refer to the user manual included with each separate piece of equipment. Wiring Diagram Monitor LCD monitor (second monitor) Personal Personal DVD player Stereo amplifier computer computer... -
Page 17: Connecting A Personal Computer
Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer's screen image. Some video cards may not display an image correctly. Connect the LCD Monitor to a Personal Computer • To connect the RGB 3 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). -
Page 18: Connecting With Digital Interface Equipment
Connecting with Digital Interface Equipment Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. Connect the LCD Monitor to a Computer with a Digital Output • To connect the RGB 2 IN connector (DVI-D) on the LCD monitor, use a DVI-D cable. Select RGB 2 from the INPUT button on the LCD monitor or DVI-D button on the remote control. -
Page 19: Connecting A Dvd Player With Component Out/Hdmi Out/Dvi Out
Connecting a DVD Player with component out / HDMI out / DVI out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player owner’s manual for more information. Connect the LCD Monitor to a DVD Player •... -
Page 20: Connecting To A Vcr/Stereo Amplifi Er
Connecting to a VCR / Stereo Amplifi er You can connect your VCR / stereo amplifi er to your LCD monitor. Refer to your VCR / stereo amplifi er owner's manual for more information. Connect the LCD Monitor to a VCR / Stereo Amplifi er •... -
Page 21: Basic Operation
Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on or red in off mode. The monitor can be powered on or off using the following three options: 1. Pressing the Main Power Switch. NOTE: When the Main Power Switch is used to power off the LCD monitor, the remote control and the power button will... -
Page 22: Power Indicator
Power Indicator NORMAL: Display by the inputed signal aspect ratio by PC signal, or display in 4:3 aspect ratio at DVD/HD or VIDEO signal. Status FULL: Display in entire screen. Power ON Green DYNAMIC: Expand 4:3 pictures to the entire screen with Power OFF non-linearity. -
Page 23: Information Osd
Information OSD RGB1, 2, 3, 4, 5 RGB3 Video Input mode 1024 x 768 Input signal Information 48kHz 60Hz AUDIO : 1 Audio input mode SIZE : FULL Picture Size mode DVD/HD DVD/HD Video Input mode AUDIO : 3 Audio input mode SIZE : FULL Picture Size mode VIDEO<S>, VIDEO... -
Page 24: Osd (On-Screen-Display) Controls
OSD (On-Screen-Display) Controls Press SET button Press MENU or Press MENU button to Press UP or DOWN, and PLUS or to decide. EXIT button to exit. open Main menu. Press MINUS button to select function, UP or DOWN button to or control which you like. -
Page 25: Picture
Main-Menu PICTURE BRIGHTNESS Adjusts the overall image and background screen brightness. Press + button to increase brightness. Press - button to decrease brightness. CONTRAST Adjusts the image brightness in relation to the input signal. Press + button to increase contrast. Press - button to decrease contrast. - Page 26 AUTO BRIGHTNESS This function controls the screen brightness depending on the ambient light for easy viewing. In addition, it changes the screen brightness depending on the ambient light and what are displayed on the screen to reduce power consumption as low as possible. [AUTO BRIGHTNESS] LOCAL: The auto brightness function is enabled.
-
Page 27: Screen
Main-Menu SCREEN H POSITION Controls Horizontal Image position within the display area of the LCD. Press + button to move screen to right. Press - button to move screen to left. V POSITION Controls Vertical Image position within the display area of the LCD. Press + button to move screen to UP. -
Page 28: Audio
Main-Menu AUDIO BALANCE Adjust the balance of L/R volume. Press + button to move the stereo sound image to right. Sound of the left side will be small. Press - button to move the stereo sound image to left. TREBLE To accentuate or reduce the high frequency sound. -
Page 29: Configuration 1
Main-Menu CONFIGURATION 1 AUTO SETUP * : INPUT RGB3, 4, 5 only Press “SET” button to automatically adjust screen size, horizontal position, vertical position, clock, clock phase, white level and black level. Press “EXIT” button to cancel execution AUTO SETUP and then will return to the previous menu. AUTO ADJUST * : INPUT RGB3, 4, 5 only Selecting the auto adjust ON/OFF. -
Page 30: Configuration 2
Main-Menu CONFIGURATION 2 CAT5 CABLE LENGTH [CAT5 CABLE LENGTH] Select the cable length, and the defaults of all the adjustment values are automatically determined. Select the length that is closest to the actual length of your cable. [CAT5 EQ] Make adjustment so that blur and smear of the displayed letters and graphic objects are minimized. [CAT5 R-GAIN, G-GAIN, B-GAIN] When the displayed image is dark, increase each value. -
Page 31: Advanced Option
Main-Menu ADVANCED OPTION INPUT RESOLUTION * : INPUT RGB3, 4, 5 only Selects to decision of input signal about below timings, 1024x768, 1280x768 and 1360x768. AUTO: Determines the resolution automatically. 1024x768: Determines the resolution as 1024x768 1280x768: Determines the resolution as 1280x768 1360x768: Determines the resolution as 1360x768 The setting you select becomes effective when POWER is turned OFF and ON again. -
Page 32: English
HEAT STATUS Information of status for COOLING FAN, BRIGHTNESS and TEMPERATURE. COOLING FAN comes to run when inside temperature is over a guaranteed limit. In this case warning is displayed on the screen. POWER ON DELAY Adjusts the delay time from “standby” to “power on” mode. “POWER ON DELAY”... -
Page 33: Note
As with all personal display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. -
Page 34: Pip, Pop And Side By Side
< PIP, POP and SIDE BY SIDE > The following table shows the combination of signal inputs under which the “PIP” and “POP” modes function. These modes do not function, however, when the screen size is “CUSTOM” or “REAL”. RGB1 RGB2 RGB3 RGB4... -
Page 35: Remote Control Numbering Function
To use a computer to control the monitors When using a computer to control the monitors, you must prepare an application software program for control by yourself. 1. Connect the RS-232C IN connector of the Master monitor shown above and the RS-232C connector of the computer using an RS-232C cable. -
Page 36: Controlling The Lcd Monitor Via Rs-232C/Rs-485 Remote Control
Controlling the LCD monitor via RS-232C/RS-485 Remote Control This LCD monitor can be controlled by the computer connected by an RS-232C cable or a CAT5 cable via the supplied CAT5 Tx BOX. Functions that can be controlled by a personal computer are: •... -
Page 37: English
3) Control sequence (1) The command from a computer to the LCD monitor will be sent in 600 ms. (2) The LCD monitor will send a return command 600 ms* after it has received and encoded. If the command isn’t received correctly, the LCD monitor will not send the return command. -
Page 38: Features
Allows you to use the entire screen area in most resolutions, signifi cantly expanding image size. Wall Mounting Interface: Allows for the monitor to be mounted on a wall or an arm using any third party compliant device. MITSUBISHI ELECTRIC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America. -
Page 39: Troubleshooting
NOTE: As with all personal display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. Image is unstable, unfocused or swimming is apparent •... -
Page 40: English
No Sound • Check to see if speaker cable is properly connected. • Check to see if mute is activated. • Check to see if volume is set at minimum. Remote Control is not available • Check the Remote Control’s batteries status. •... -
Page 41: Specifi Cations
Specifi cations Specifi cations (MDT521S) Product Specifications Analog Input Digital Input LCD Module Diagonal: 52" / 132.2 cm Pixel Pitch: 0.600 mm Resolution: 1920 x 1080 dots Color: Over 16 million colors (depending on video card used) Brightness: 700 cd/m (typ.) Contrast Ratio: 2000:1... -
Page 42: Pin Assignment
Pin Assignment 1) Analog RGB input (Mini D-SUB 15P): RGB3 Pin No Name Video Signal Red Video Signal Green Video Signal Blue Mini D-SUB 15P DDC-GND Red-GND Green-GND Blue-GND +5V (DDC) SYNC-GND DDC-SDA H-SYNC V-SYNC DDC-SCL 2) Analog RGB input (CAT5): RGB5 Pin# at RJ45 Signal Pair... -
Page 43: English
5) S-VIDEO input (MINI DIN 4P): VIDEO<S> MINI DIN 4P Pin No Name Y (Luminance) C (Chroma) 6) RS-232C input/output Pin No Name Mini D-SUB 9P English-42... - Page 44 :projector.info@meuk.mee.com Technical Phone :+44 (870) 606 5008 :+44 (1506) 431927 E-mail :projector.info@meuk.mee.com Russia (Mitsubishi Electric Europe B.V Moscow Representative Office) 52, bldg.5, Kosmodamianskaya Nab, 113054, Moscow, Russian Federation Sales Phone :+7 (095) 721 2070 :+7 (095) 721 2071 Technical Phone...