Chapters
Table of Contents
Related Manuals for Miele T 8322
Summary of Contents for Miele T 8322
-
Page 1: Operating Instructions
Operating instructions for vented tumble dryer T 8322 en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. M.-Nr. 07 127 330... -
Page 2: Caring For The Environment
Caring for the environment Disposal of the packing Energy saving tips material To avoid unnecessarily long drying times and high consumption of energy: The transport and protective packing has been selected from materials which – Make sure that your laundry is are environmentally friendly for disposal thoroughly spun before drying. -
Page 3: Table Of Contents
Contents Caring for the environment ......... . 2 Warning and Safety instructions . - Page 4 Contents Installation and connection ........31 Front view .
-
Page 5: Warning And Safety Instructions
Any other applications may be property. dangerous. Miele cannot be held liable for damage resulting from incorrect or To avoid the risk of accidents and improper use or operation. damage to the tumble dryer, please... - Page 6 Do not install or use a damaged tumble dryer. If the connection cable is faulty it must only be replaced by a Miele Before connecting the tumble dryer, approved service technician to protect ensure that the connection data on the the user from danger.
-
Page 7: Correct Use
Warning and Safety instructions Correct use To prevent the risk of fire, the following must not be dried in this To prevent the risk of fire, the tumble dryer: following textiles must not be dried in this tumble dryer: – fabrics which contain a large proportion of rubber, foam rubber or –... - Page 8 Warning and Safety instructions The dryer must not be used without Adequate ventilation is essential to the fluff filter in place or if the fluff filter is avoid the danger of asphyxia and damaged in any way. toxic fumes where another appliance which also uses the room air (e.g.
- Page 9 – pets or other small animals climbing into it. The tumble dryer must not be hosed down. Accessories Only use genuine Miele spare parts and accessories with this appliance. If non-Miele parts are used, guarantee, performance and product liability claims may be invalidated.
-
Page 10: Operating The Tumble Dryer
Operating the tumble dryer Control panel a Low temperature button f Check lights Delicate fabrics are dried at a lower For a description of these lights see: "Problem solving guide" / "After sales temperature. service". b Drying level button g Start/Stop button with indicator lights For starting the programme selected c Display... - Page 11 Operating the tumble dryer Display In the same way, the Woollens handcare, Silks handcare and The following are selected via the Smoothing programmes can finish display: earlier than expected if a certain – Delay start temperature is reached. This can happen with particularly fine fabrics, –...
-
Page 12: Notes On Laundry Care
Notes on laundry care Care symbols – Down-filled garments have linings which have a tendency to shrink, Before drying check the drying symbol depending on the quality of the item. on the care label. If there are no They can be partially dried using the symbols, dry at your own risk! Smoothing programme. -
Page 13: How To Dry Correctly
How to dry correctly Brief instructions C Load the tumble dryer ^ Press the Door button to open the The headings numbered (A, B, C ...) show the operating sequence and can door. be used as a brief guide to using your ^ Load the laundry loosely into the dryer. - Page 14 How to dry correctly D Select a programme Important: Please note that the programme duration shown in the display will vary according to the programme selected (see "Programme duration/Estimated time remaining"). The Woollens handcare, Silks handcare and the Smoothing programmes cannot be changed.
- Page 15 How to dry correctly F Start the programme G Remove the laundry when the programme has finished The Start/Stop button will flash when a programme is being selected. The 0 and Finish will appear in the display flashing indicates that a programme to indicate that the programme has can be started.
-
Page 16: Extra Options / Delay Start
Extra options / Delay start Low temperature To begin delay start ^ Press the Start/Stop button. For all delicate or minimum iron fabrics with the r symbol on the care – The Delay start indicator light will label (e.g. acrylic garments). light up constantly. -
Page 17: Programme Chart
Programme chart Cottons Max. load: 6 kg* Extra dry, Normal** Fabric type Single and multi-layered cotton fabrics such as towelling, jerseywear, T-shirts, underwear. Notes – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for jersey fabrics (e.g. T-shirts, underwear), as they have a tendency to shrink. -
Page 18: Smoothing
Programme chart Woollens handcare Max. load: 2 kg* Fabric type Woollen fabrics Note – This programme only fluffs up woollen garments. – Fabrics are not completely dried in this programme. Remove garments as soon as the programme has finished and leave to finish drying at room temperature. Low temperature Low temperature cannot be deselected. -
Page 19: Outerwear Normal
Programme chart Automatic Max. load: 3.5 kg* Normal, Hand iron Fabric type Mixed loads of garments suitable for the Cottons and Minimum iron programmes. Sort according to colour. Shirts Max. load: 2 kg* Normal, Hand iron Fabric type Shirts and blouses. Low temperature Select the Low temperature option for delicate fabrics with the r symbol on the care label. -
Page 20: Changing The Programme Sequence
Changing the programme sequence Once a programme has started Adding or removing laundry after a programme has started - changing the programme ^ Press the Door button. You cannot change to another ^ Open the door. programme once a programme has started (this prevents unintentional Danger of burning: alterations). -
Page 21: Electronic System Lock
Electronic system lock D Now slowly turn the programme The system lock prevents the dryer selector six positions stage by stage being used without your knowledge. in an anti-clockwise direction. Each of the six programme indicator It can be activated if wished. lights must come on one after the other. -
Page 22: Cleaning And Care
You could also use a cleaning brush which is available as an optional extra from your Miele dealer or the Miele Spare Parts Department, or use a vacuum cleaner. ^ Also clean the door seal (2) with a damp cloth. -
Page 23: Cleaning The Grilles In The Door Opening
Miele branded cleaning and conditioning products are available to order from your Dealer, the Miele Spare Parts Department or via the internet on www.miele-shop.com. ^ Clean the housing, control panel and door seal with a slightly damp cloth and a mild detergent or soapy water. -
Page 24: Problem Solving Guide
Cooling down or then on again. Finish flashes in the – Then start the display. programme again. The buzzer sounds. If the programme stops again and Cooling down or Finish flashes again there is a fault. Contact the Miele Service Department. - Page 25 – Open and close the door. airways – Switch the dryer off and indicator light then back on again. comes on. – Then start the programme The buzzer again. sounds. – If the Clean out airways indicator light comes on, contact the Miele Service Dept.
-
Page 26: Other Problems
Problem solving guide Other problems Problem Possible cause Remedy The drying Please check all the possible causes and switch the process goes on dryer off and then back on again. too long or even Ventilation to the dryer is Open a door or window while switches off. - Page 27 Problem solving guide Problem Possible cause Remedy Items made of synthetic Synthetic fibres tend to Static charge can be fibres are charged with attract static charge. reduced by adding a static electricity after fabric conditioner to the drying. final rinse in the washing programme or a fabric conditioner sheet to the load when drying.
- Page 28 Problem solving guide Problem Possible cause Remedy The tumble dryer fails to No obvious cause. – Is the dryer switched start when switched on. – Is the plug correctly inserted into the socket and switched on? – Is the door closed properly? –...
-
Page 29: Changing The Lamp
^ Apply a little pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover. The cover will open downwards. The temperature resistant lamp should only be ordered from your Miele Dealer or the Miele Spare Parts Department. -
Page 30: After Sales Service
Miele Dealer, the the data plate situated on the right hand Miele Spare Parts Department or via the side below the drum aperture. internet at www.miele-shop.com. Please note that telephone calls may be monitored and recorded for training purposes. -
Page 31: Installation And Connection
Installation and connection Front view a Venting connection: rear, right or left (supplied with the rear socket open) b Mains connection cable c Control panel d Door e Four height adjustable screw feet... -
Page 32: Rear View
– 870-885 / 915-930 mm, one or two the dryer. To manoeuvre the dryer out of raising kits* are required. its packing case to its installation site * Miele accessory available to order you will also need to hold it by the front feet. Replacing the lid Do not lift the appliance by the door. -
Page 33: Levelling The Appliance
Washer-dryer stack The tumble dryer can also be combined with a Miele washing machine in a washer-dryer stack. The appropriate "WTV" stacking kit (available to order) to match your dryer The appliance must be perfectly level to is required. -
Page 34: Electrical Connection
Electrical connection Electrical connection U.K. Non-rewireable plugs BS 1363 All electrical work should be carried out The fuse cover must be refitted when by a suitably qualified and competent changing the fuse, and if the fuse cover person, in strict accordance with is lost, the plug must not be used until a current national and local safety suitable replacement is obtained. -
Page 35: Installation - Venting
– The ducting outlet (e.g. wall pipe) * Available as an optional accessory should be installed in such a way that from your Miele dealer or the Miele the moist expelled air . . . Spare Parts Department..cannot be drawn back into the room in which the dryer is installed;... -
Page 36: Calculating The Effective Duct Length
Venting connection to the 1.0 m require straight ducting. Multiply this left/right amount by the corresponding *optional accessory from Miele additional duct length factor in Table I. ^ Establish the number of angles, Table II bends etc. necessary and add their... -
Page 37: Installation To The Rear, Left Or Right Side Of The Appliance
Installation - venting Installation to the rear, left or Calculation example right side of the appliance At the rear The dryer is delivered with this connection open. ^ Fit one of the venting systems described on the following pages. Left or right side of the appliance Wall pipe, with louvred vent = 1 x 3.8 m Additional duct = 3.8 m... -
Page 38: Venting Systems
^ The following items are required: ..flexible ducting hose . . . a wall vent kit* or window vent kit*. * (Miele optional accessory). A Insert adapter (1) into the vent opening on the dryer. - Page 39 Installation - venting Installation examples Connection to an exhaust flue Window vent 1. Pipe with connection piece (= supplied with the Miele wall vent 1. Window vent kit (fitted in a kit) "plexiglass" pane) (separate fitting instructions are 2. Adapter for flexible hose supplied with the Miele window vent 3.
-
Page 40: Plastic Piping
(Separate fitting instructions are is more than 100 mm, an adapter is necessary (e.g. from C 100 to 125 supplied with the Miele wall vent kit). 2. Adapter mm) to connect the pipe to the dryer. 3. Plastic piping, diameter DN 100... -
Page 41: Connect Directly To A Wall Vent
(* Miele optional accessories). A Before drilling into the wall, ..please read the installation instructions supplied with the Miele wall vent kit..and study the following diagrams. 1. Wall pipe 2. -
Page 42: Washer-Dryer Stack
Example: Miele washing machine with straight or sloping fascia Stacking kit* without pull-out shelf: A = 94.2 cm B = 170.0 cm Stacking kit* with pull-out shelf: A = 92.8 cm B = 168.6 cm * Miele accessory available to order... -
Page 43: Consumption Data
Consumption data Programme Load Final spin speed Energy Duration in a domestic washing machine Minutes Cottons 1000 (60 % residual moisture)** 3.20 Normal 1200 2.90 1400 2.75 1600 2.45 1800 2.40 Cottons 1000 (60 % residual moisture)** 2.45 Hand iron 1200 2.15 1400... -
Page 44: Technical Data
Technical data Height 850 mm Height for building under 820 mm Width 595 mm Depth 580 mm Depth with door open 1,060 mm Suitable for pushing under a worktop Suitable for stacking Weight 45 kg Drum volume 111 litres Maximum capacity 6 kg dry weight Length of connection cable Voltage... -
Page 45: Programmable Functions For Changing Default Settings
Programmable functions for changing default settings The programmable functions are used to alter the tumble dryer´s electronics to suit changing requirements. Programmable functions can be altered at any time. -
Page 46: Programmable Functions
Programmable functions Extending the range of the – The Low temperature indicator light will briefly flash on and off twice. drying levels – P and 0 (default setting) will flash You can extend the range of the alternately in the display. drying levels for many of the The number which appears alternately programmes:... -
Page 47: Altering The Volume Of The Buzzer
Programmable functions Altering the volume of the A Press the Start/Stop button and keep it pressed in whilst carrying out steps buzzer B-C. The buzzer has two volumes. B Press the I-On/0-Off button in. Normal Wait until the indicator light for the The buzzer sounds at the end of a Start/Stop button lights up programme (default setting). -
Page 48: Memory Function
Programmable functions Memory function A Press the Start/Stop button and keep it pressed in whilst carrying out steps The electronics will memorise any B-C. extra options selected for a B Press the I-On/0-Off button in. programme. The duration selected for the timed Wait until the indicator light for the drying programmes will also be Start/Stop button lights up... -
Page 49: Extending The Cooling Down Time
Programmable functions Extending the cooling down A Press the Start/Stop button and keep it pressed in whilst carrying out steps time B-C. The cooling down phase which takes B Press the I-On/0-Off button in. place before the end of a programme Wait until the indicator light for the can be lengthened if required. -
Page 50: Clean Out Airways Indicator
Programmable functions Clean out airways indicator A Press the Start/Stop button and keep it pressed in whilst carrying out steps Fluff should be removed after drying. B-C. The Clean out airways indicator will B Press the I-On/0-Off button in. remind you to clean the filters when a Wait until the indicator light for the certain amount of fluff has collected Start/Stop button lights up... -
Page 51: Keypad Tone
Programmable functions Keypad tone A Press the Start/Stop button and keep it pressed in whilst carrying out steps An audible tone sounds each time a B-C. button is pressed. B Press the I-On/0-Off button in. Follow steps A to F to programme Wait until the indicator light for the and store in memory. -
Page 52: Adjusting The Dryer's Electronics For Very Soft Water
Programmable functions Adjusting the dryer's A Press the Start/Stop button and keep it pressed in whilst carrying out steps electronics for very soft water B-C. Extremely soft water can affect B Press the I-On/0-Off button in. the sensitivity of the control Wait until the indicator light for the electronics. - Page 56 Alteration rights reserved/2008 M.-Nr. 07 127 330 / 01...