Table of Contents
Advertisement
Range Hood
Use & Care / Installation Manual
Models
FSH301-WH
FSH301-SS
FSH301-BL
FSH361-WH
FSH361-SS
FSH361-BL
V05650 rev.D
®
(30" wide - White)
(30" wide - Stainless)
(30" wide - Black)
(36" wide - White)
(36" wide - Stainless)
(36" wide - Black)
HB0026
!
INTENDED FOR DOMESTIC COOKING ONLY
F
S
, Cleveland, TN 37320-2490
IVE
TAR
FSH481-WH
(48" wide - White)
FSH481-SS
(48" wide - Stainless)
FSH481-BL
(48" wide - Black)
FSH601-WH
(60" wide - White)
FSH601-SS
(60" wide - Stainless)
FSH601-BL
(60" wide - Black)
!
www.fivestarrange.com
Advertisement
Table of Contents
Related Manuals for FiveStar FSH301-BL
Summary of Contents for FiveStar FSH301-BL
-
Page 1: Range Hood
Range Hood Use & Care / Installation Manual Models FSH301-WH FSH301-SS FSH301-BL FSH361-WH FSH361-SS FSH361-BL V05650 rev.D ® FSH481-WH (30” wide - White) FSH481-SS (30” wide - Stainless) FSH481-BL (30” wide - Black) FSH601-WH (36” wide - White) FSH601-SS (36” wide - Stainless) FSH601-BL (36”... -
Page 2: Table Of Contents
READ AND SAVE THESE INSTRUCTIONS SECTION ... PAGE Warranty ... 2 Safety Instructions ... 3 Operation ... 4 Cleaning ... 4 Parts Included With Hood ... 5 Parts Not Included With Hood ... 5 Optional Parts ... 5 Tools Needed ... 5 LIMITED WARRANTY This product has been designed for domestic household use. -
Page 3: Safety Instructions
WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address listed in the warranty. 2. -
Page 4: Operation
OPERATION Always turn ON your hood before you begin cooking in order to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter. HC0004 1. -
Page 5: Parts Included With Hood
PARTS INCLUDED WITH HOOD Wood mounting strip Grease Filters (3 per 30’’ and 36’’ hood) (4 per 48’’ hood) (5 per 60’’ hood) Parts Bag (includes 4 flat head screws #10-2’’, 8 screws #8-3/4’’, 4 Nuts #10-32, 2 Wall anchors and 2 Washers 3/16’’... -
Page 6: Five Star Range Hood System
Wall & Roof Caps, Exterior Blower Model 332H (900 cfm) Exterior Blower Elbows and In-Line Dampers Model 418 10’’ Round Adjustable Elbow Ductwork Choose 1 of 5 Discharge Transitions Model 427 Model 423 (4 ½’’ x 18 ½’’ (4 ½’’ x 18 ½’’ to to 10’’... -
Page 7: Prepare The Hood Location
PREPARE THE HOOD LOCATION 1. The F hood must be installed with interior blower models FBK600 or FBK1200, or exterior blower model 332H only. Other blowers cannot be substituted. (Blowers sold separately.) Plan where and how the ductwork will be located. Install proper-sized ductwork, transition(s), elbow(s), and roof or wall cap for the model of blower you are using. -
Page 8: Prepare The Hood
1. Using a Phillips #2 or a Robertson #2 screwdriver, unscrew the hood from the bottom of crate. Refer to figure to the right to locate all 4 screws. Discard these screws and remove hood from wood pallet. OPTION A Backsplash is available (see page 5 for more details). This backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting screws. -
Page 9: Install The Hood
1. Rest the back cavity of the hood on the wood mounting strip. CAUTION: Hold the hood until it is completely secured to the wood mounting strip. Secure hood to wood strip with (4) screws #8 - 3/4” (for 30” and 36” width hoods) or (6) screws (for 48” and 60’’ width hood) provided at location shown. -
Page 10: Connect The Wiring
WARNING: Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. 120V 60Hz IN NEMA 5-15P PLUG... -
Page 11: Install The Filters
CAUTION: Remove protective plastic film covering filters before installing them. It is recommended to install side filters first and finish with center one(s). 1) Insert upper end of filter into the hood (pull tab side). 2) Raise lower end toward the inside of hood. 3) Position rear part of filter into channel and pull. -
Page 12: Service Parts
HL0031 KEY NO. PART NO. DESCRIPTION V05616 Logo V02264 Porcelain Lamp Socket V02773 Male Motor Connector V02772 Female Motor Connector V03435 Thermostat V03436 Thermostat Bracket V02563 SPST Single Switch for Heat Lamps V03502 SPST Double Switch for Halogen Lights V03503 SPST Lighted Single Switch for Blower V03504...