Summary of Contents for ACR Electronics PathFinder3 SART-3
Page 1
PRODUCT SUPPORT MANUAL PathFinder™ Search and Rescue Transponder Model No.: SART-3 Product No.: 2714, 2714NH Y1-03-0170 Rev. H...
Page 2
Frequently Asked Questions (FAQs) section for further information or call our Technical Service Department. The website address is www.acrelectronics.com. If in the future you lose this manual, you may access and print a replacement on the ACR website. Y1-03-0170H...
SECTION 1 - HOW THE PATHFINDER™ WORKS The PathFinder™ helps search and rescue services to quickly locate a life raft in the event of a rescue at sea. The SART can either be stowed in a life raft, or mounted next to emergency exits and then carried to the life raft in an emergency.
Quantity Item PathFinder™ search and rescue transponder Mounting bracket Product Support Manual Warranty card If you do not have all of the items, please call ACR Technical Service at +1 (954) 981-3333. Y1-03-0170H...
Page 6
Controls and indicators Antenna Pull Tab Lock Activation Switch Ring Pull Tab Control and Battery Housing Hanging Lanyard Lanyard Spool Telescopic Pole Rotate bottom cap to release lanyard and telescopic pole Figure 2 Y1-03-0170H...
Vessel name The SART label has a space where the vessel name is marked (see Figure 3). This can be done as follows. With an indelible pen, write the vessel name directly onto the SART. Note, however, that some indelible inks will fade when exposed to strong sunlight, so a ultra-violet (UV) resistant pen is recommended.
Page 8
CAUTION: Keep this SART at least 3 feet (1 meter) away from all magnetic sources, stereo speakers and compass installations. Installation The SART mounting bracket should be bolted to a bulkhead using four (4) suitable M6 (1/4") bolts. Mounting hardware for the bracket is not included. Hardware required depends on the bulkhead material and its thickness.
Page 9
NOT TO SCALE Figure 4: Installing the SART Y1-03-0170H...
SECTION 4 - OPERATION Sequence of Operations The SART has primary and secondary indicating systems: The primary system is the indicator lights and the secondary system is the buzzer. When the switch is set to ON, the SART immediately enters the Test Mode. Here both the red light and the buzzer are tested.
Page 11
When activated the SART has three modes of operation: Receive - waiting for a valid interrogation by a radar signal. Reply - replying to a valid interrogation by a valid radar signal. Test - self-test sequence that checks both indicator lights and the buzzer.
Page 12
Pole Mounted SART 1. The PathFinder™ is supplied with a telescopic pole to raise the SART one meter above sea level (see figure 6). 2. To operate, simply turn the bottom cap of the SART to release the pole. 3. Pull the pole downward and extend it to its maximum length. 4.
Page 13
Hanging SART 1. If no pole is available, or if you prefer, you can suspend the SART from the canopy support using the additional lanyard loop provided (see Figure 7). 2. Loop the lanyard through the support strap in the life raft and secure firmly.
SECTION 5 - MAINTENANCE This chart is a summary of the procedures described below. Time interval Maintenance to do Every two months Visual inspection Battery expiry date check Pole operation check Lanyard check Safety lock check Confidence check Every year Functional test Every-two-months inspection The SART is a safety device;...
Page 15
WARNING: The battery pack cannot be recharged; attempts to recharge the battery pack could result in an explosion or fire. Replacement of the SART battery pack must be performed by ACR or by an authorized ACR Battery Replacement Center. The cost of this replacement is the responsibility of the owner.
1 (one) year* from date of purchase or receipt as a gift. During the warranty period ACR Electronics, Inc. will repair or, at its option, replace the unit at no cost to you for labor, materials and return transportation from ACR. For further assistance, please contact our Technical Service Department at ACR Electronics, Inc., 5757 Ravenswood Road, Fort Lauderdale, FL 33312-6645.
EC DECLARATION OF CONFORMITY ACR Electronics hereby declares that the following product is in conformity with Council Directive 96/98/EC of 20 December 1996 on Marine Equipment (MED) last amended by Commission Directive 2008/67/EC of 30 June 2008, and has been type examined as described in this Declaration. In accordance with the...
Page 19
Assemblies include population of components, solder and interconnects. Product Marking Explanations In accordance with the requirements specified in SJ/T11364–2006, all ACR EIPs sold in the People’s Republic of China are marked with a pollution control marking. The following marking applies to ACR products.