Related Manuals for AMAV VGA44
Summary of Contents for AMAV VGA44
- Page 1 V G A 4 4 4 X 4 VG A M ATR IX SW ITCHER I N S TA L LATI O N A N D O PER ATIO N M ANUAL VGA44 manual.indd 12/3/07 2:24:58 PM...
- Page 2 18. Do not ground any red (“hot”) terminal. Never connect a “hot” (red) output to ground or to another “hot” (red) output! 8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage 19. Non-use periods. The power cord of equipment should be unplugged is not covered by any warranty. from the outlet when left unused for a long period of time. 9. Have gain controls on amplifiers turned down during power-up 20. Service Information Equipment should be serviced by qualified service to prevent speaker damage if there are high signal levels at the inputs. personnel when: 10 Power down & disconnect units from mains voltage before making A. The power supply cord or the plug has been damaged. connections. B. Objects have fallen, or liquid has been spilled into the equipment 11. Never hold a power switch in the “ON” position if it won’t stay there itself! C. The equipment has been exposed to rain 12. Do not use the unit near stoves, heat registers, radiators, or other heat D. The equipment does not appear to operate normally, or exhibits a marked producing devices. change in performance E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL VGA44 manual.indd 12/3/07 2:24:58 PM...
-
Page 3: I N T R O D U C T I O N A N D C O N T E N T S
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. V G A 4 4 I N S TA L L AT I O N & O P E R AT I O N M A N U A L PA G E 3 VGA44 manual.indd 12/3/07 2:24:58 PM... -
Page 4: Front And Rear Panel
PA G E 4 V G A 4 4 I N S TA L L AT I O N & O P E R AT I O N M A N U A L VGA44 manual.indd 12/3/07 2:24:59 PM... - Page 5 - Rcvd V G A 4 4 I N S TA L L AT I O N & O P E R AT I O N M A N U A L PA G E 5 VGA44 manual.indd 12/3/07 2:24:59 PM...
-
Page 6: Operation
O P E R AT I O N Before making any connections to the VGA44, observe the OPERATION following: > Connect all audio video sources and destination equipment > Before making any connections to the VGA44, observe the following: > Power up all source and destination audio-visual sources > Ensure the mains voltage supply matches the label on the supplied > Power up the VGA44 VGA matrix switcher plug-pack (+/- 10%) > For each destination output select the appropriate input source by using > Ensure that the power switch is OFF the front panel UP and DOWN select button, the supplied IR remote control, or through the RS232 serial communications port > Ensure that all system grounds (earth) are connected to a common point. Avoid powering equipment within a system from multiple power sources that may be separated by large distances REMOTE CONTROL The AMAV VGA44 matrix switcher ships with a remote control. The remote control has the following functionality: i) Source Select Buttons Four separate input assignment buttons are provided for each of the four VGA outputs. The last selected input source will be routed to the destination output. Input sources may be assigned to multiple destination outputs ii) Power Button Toggles the unit into, and out of, standby mode. In standby mode the... - Page 7 2.2 kg V G A 4 4 I N S TA L L AT I O N & O P E R AT I O N M A N U A L PA G E 7 VGA44 manual.indd 12/3/07 2:25:00 PM...
-
Page 8: Australia And New Zealand
. a u w w w. a u s t r a l i a n m o n i t o r. c o m INTERNATIONAL SALES SENNHEISER ELECTRONIC CORPORATION 1 Clyde Street Silverwater NSW 2128 Australia 1 Enterprise Drive...
Need help?
Do you have a question about the VGA44 and is the answer not in the manual?
Questions and answers