Using voice dialing ...............9 Adjusting the headset volume........10 Switching between the headset and phone.... 10 Erasing all pairing information........10 Turning the indicator on or off........10 Checking the battery status ........... 11 Resetting the headset (hardware reset)..... 11 RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
To reduce the risk of fire or electric shock, do not expose the charger to rain, moisture, dripping, or splashing. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
Note: Your RF-QX4 model number may end in a letter depending on what region you are in. We use RF-QX4 in this User Guide to refer to all of the following models: •...
Incoming call—Flashes green two times every 1 second. Active call—Flashes green every 5 seconds. Power off—Lights solid red for 1 second and the headset beeps once. Low battery—Alternately flashes red and green, and the headset beeps every 300 seconds. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
+ (volume up) buttons for three seconds. Turn the indicator off When the headset is connected to a phone, press and hold the Power/Send/End and – (volume down) buttons for three seconds. Check the battery status Press and hold the Power/Send/End for two seconds. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
(10 meters) of the headset. Turn on the headset and make sure that the battery is fully charged. Press and hold the Power/Send/End button for about four seconds. The indicator rapidly flashes green. Release the button. The headset is now in pairing mode. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
Set the phone to start searching for Bluetooth devices. Select RF-QX4 from the list of found devices displayed on the phone. If necessary, enter the PIN code 0000 to pair and connect the headset with your phone.
To use voice dialing: • When no call is in progress, press the Power/Send/End button. A tone indicates that you can start saying the voice tag. The phone plays the voice tag and dials the related phone number. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
• At the same time, press the Power/Send/End button and the + (volume up) button for about three seconds to turn on the indicator. • At the same time, press the Power/Send/End button and the – (volume down) button for about three seconds to turn off the indicator. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
• Do not drop, knock, or shake the headset. Rough handling can break internal circuit boards and fine mechanics. • Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the headset. • Do not paint the headset. Paint can clog the moving parts and prevent correct operation. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
This equipment complies with RSS210 of the IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. RF-QX4/RF-QX4-T/RF-QX4-E/RF-QX4-J...
Product is determined to be defective by an authorized Rocketfish repair center or store personnel, Rocketfish will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no charge with new or rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of Rocketfish and are not returned to you.
Page 14
Damage due to incorrect operation or maintenance • Connection to an incorrect voltage supply • Attempted repair by anyone other than a facility authorized by Rocketfish to service the Product • Products sold as is or with all faults •...