Hobart Welding Products IronMan 275 Owner's Manual
  1. Manuals
  2. Brands
  3. Hobart Welding Products Manuals
  4. Welding System
  5. IronMan 275
  6. Owner's manual
Hobart Welding Products IronMan 275 Owner's Manual

Hobart Welding Products IronMan 275 Owner's Manual

With meters and m-25 gun
Hide thumbs
Table of Contents

Advertisement

Quick Links

Visit our website at
www.HobartWelders.com
IronMan 275
With Meters
And M-25 Gun
OM-198 683C
April 2000
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
Description
Arc Welding Power Source
and Wire Feeder
R

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IronMan 275 and is the answer not in the manual?

Questions and answers

Related Manuals for Hobart Welding Products IronMan 275

Summary of Contents for Hobart Welding Products IronMan 275

  • Page 1 OM-198 683C April 2000 Processes MIG (GMAW) Welding Flux Cored (FCAW) Welding Description Arc Welding Power Source and Wire Feeder IronMan 275 With Meters And M-25 Gun Visit our website at www.HobartWelders.com...
  • Page 2 From Hobart to You Thank you and congratulations on choosing Hobart. Now you can get the job done and get it done right. We know you don’t have time to do it any other way. This Owner’s Manual is designed to help you get the most out of your Hobart products.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING ......1-1.

  • Page 5: Section 1 - Safety Precautions - Read Before Using

    SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING som _nd_4/98 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. This group of symbols means Warning! Watch Out! possible Y Marks a special safety message.
  • Page 6 ARC RAYS can burn eyes and skin. BUILDUP OF GAS can injure or kill. D Shut off shielding gas supply when not in use. Arc rays from the welding process produce intense D Always ventilate confined spaces or use visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin.

  • Page 7: Additional Symbols For Installation, Operation, And Maintenance

    1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. MOVING PARTS can cause injury. D Do not install or place unit on, over, or near D Keep away from moving parts such as fans. combustible surfaces. D Keep all doors, panels, covers, and guards D Do not install unit near flammables.

  • Page 8: Emf Information

    1-5. EMF Information Considerations About Welding And The Effects Of Low Frequency 1. Keep cables close together by twisting or taping them. Electric And Magnetic Fields 2. Arrange cables to one side and away from the operator. Welding current, as it flows through welding cables, will cause electro- magnetic fields.

  • Page 9: Section 1 - Consignes De Securite - Lire Avant Utilisation

    SECTION 1 – CONSIGNES DE SECURITE – LIRE AVANT UTILISATION som _nd_fre 4/98 1-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette procédure présente des risques de danger ! Ceux-ci sont identifiés par des symboles adjacents aux directives. Ce groupe de symboles signifie Mise en garde ! Soyez vigilant ! Il y a des Y Identifie un message de sécurité...
  • Page 10 LES RAYONS DE L’ARC peuvent pro- LES ACCUMULATIONS DE GAZ ris- voquer des brûlures dans les yeux et quent de provoquer des blessures ou sur la peau. même la mort. Le rayonnement de l’arc du procédé de soudage D Fermer l’alimentation du gaz protecteur en cas de génère des rayons visibles et invisibles intenses non utilisation.

  • Page 11: Dangers Supplémentaires En Relation Avec L'installation, Le Fonctionnement Et La Maintenance

    1-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance Risque D’INCENDIE OU DES ORGANES MOBILES peuvent D’EXPLOSION. provoquer des blessures. D Ne pas placer l’appareil sur, au-dessus ou à proxi- D Rester à l’écart des organes mobiles comme le mité...

  • Page 12: Principales Normes De Sécurité

    1-4. Principales normes de sécurité Safety in Welding and Cutting, norme ANSI Z49.1, de l’American Wel- Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, ding Society, 550 N.W. Lejeune Rd, Miami FL 33126 de la Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

  • Page 13: Section 2 - Installation

    SECTION 2 – INSTALLATION 2-1. Specifications Max. Open- Amps Input at Rated Output, 50 or 60 Hz, Single-Phase Rated Output Circuit 200 (208) V 230 V 400 V 460 V 575 V Voltage 250 A at 28 VDC, 200 A at 28 VDC, 40% Duty Cycle 60% Duty Cycle 2.3*...

  • Page 14: Welding Gun Duty Cycle And Overheating

    2-3. Welding Gun Duty Cycle And Overheating CAUTION WELDING LONGER THAN RATED DUTY CYCLE can damage gun and void warranty. Do not weld at rated load longer than shown below. Using gasless flux cored wire reduces gun duty cycle. warn7.1 8/93 Definition .023 To .045 in (0.6 To 1.1 mm) .023 To .045 in (0.6 To 1.1 mm) Hard Or Flux Cored Wires...

  • Page 15: Installing Work Clamp

    2-5. Installing Work Clamp Work Cable Boot Slide boot onto work cable. Route cable out front panel opening from inside. Negative (–) Output Terminal Connect cable to terminal and cover connection with boot. Hardware Work Clamp Route cable through clamp handle and secure as shown.

  • Page 16: Setting Gun Polarity For Wire Type

    2-8. Setting Gun Polarity For Wire Type Polarity Changeover Label Changing Polarity Information Always read and follow manufac- ture’s recommended polarity. Wire Drive Work Clamp Lead Assembly Lead Positive Terminal Negative Terminal Shown as shipped – Electrode Positive (DCEP): For solid steel, stainless steel, aluminum, or flux core with gas wires (GMAW).

  • Page 17: Installing Wire Spool And Adjusting Hub Tension

    2-10. Installing Wire Spool and Adjusting Hub Tension Use compression spring with 8 in (200 mm) spools. When a slight force is needed to turn spool, tension is set. Tools Needed: 15/16 in ST-072573-B 2-11. Positioning Jumper Links Check input voltage available at site.

  • Page 18: Electrical Service Guide

    2-12. Electrical Service Guide Input Voltage Input Amperes At Rated Output Max Recommended Standard Fuse Or Circuit Breaker Rating In Amperes Circuit Breaker , Time-Delay Normal Operating Min Input Conductor Size In AWG/Kcmil Max Recommended Input Conductor Length In Feet (Meters) (29) (39) (47)

  • Page 19: Threading Welding Wire

    2-14. Threading Welding Wire Wire Spool Welding Wire Inlet Wire Guide Pressure Adjustment Knob Drive Roll Outlet Wire Guide Gun Conduit Cable Lay gun cable out straight. Tools Needed: Hold wire tightly to keep it from unraveling. 6 in (150 mm) Open pressure assembly.

  • Page 20: Weld Parameter

    2-15. Weld Parameter OM-198 683 Page 16...
  • Page 21 VOL TAGE WIRE SPEED 196 843 OM-198 683 Page 17...

  • Page 22: Section 3 - Operation

    SECTION 3 – OPERATION 3-1. Controls Voltage Control Turn control clockwise to increase voltage. Wire Speed Control Turn control clockwise to increase wire feed speed. Power Switch Voltmeter Wire Feed Speed Meter 198 653 OM-198 683 Page 18...

  • Page 23: Voltmeter And Wire Feed Speed Meter Operation

    3-2. Voltmeter And Wire Feed Speed Meter Operation Voltmeter Wire Feed Speed Meter Power Up Status Both meters display zeros at unit power up. After one second, preset values appear on both meters. The MIG gun settings (not spool gun) are always the default at initial power up of the unit.

  • Page 24: Section 4 - Maintenance &Troubleshooting

    SECTION 4 – MAINTENANCE &TROUBLESHOOTING 4-1. Routine Maintenance Maintain more often Y Disconnect power during severe conditions. before maintaining. 3 Months Replace unreadable labels Repair or replace cracked weld cable Clean and tighten weld terminals 6 Months Remove drive roll and Blow out or vacuum inside.

  • Page 25: Replacing Gun Contact Tip

    4-4. Replacing Gun Contact Tip Y Turn Off power. Nozzle Contact Tip Cut off welding wire at contact tip. Remove nozzle. Remove contact tip and install new contact tip. Reinstall nozzle. Tools Needed: Ref. 800 797-C 4-5. Changing Drive Roll and Wire Inlet Guide Securing Screw Inlet Wire Guide Loosen screw.

  • Page 26: Aligning Drive Rolls And Wire Guide

    4-6. Aligning Drive Rolls and Wire Guide Y Turn Off power. View is from top of drive rolls look- ing down with pressure assembly open. Drive Roll Securing Nut Correct Incorrect Drive Roll Wire Guide Welding Wire Drive Gear Insert screwdriver, and turn screw in or out until drive roll groove lines up with wire guide.

  • Page 27: Cleaning Or Replacing Gun Liner

    4-7. Cleaning Or Replacing Gun Liner Tools Needed: Y Disconnect gun from unit first. 5/16 in, 10 mm Head Tube Remove nozzle, contact tip, and adapter. 5/16 in 10 mm Remove liner. Lay gun cable out straight before installing new liner. To Reassemble Gun: Blow out gun casing.

  • Page 28: Replacing Switch And/Or Head Tube

    4-8. Replacing Switch And/Or Head Tube Y Disconnect gun first. Remove handle locking nut. Slide handle. Remove switch housing. Note: If installing new switch, push switch lead connectors onto terminal of new switch (polarity is not important). Install switch back into handle, and secure with handle locking nut. If replacing head tube, continue to end of figure.

  • Page 29: Troubleshooting

    4-9. Troubleshooting Trouble Remedy Be sure line disconnect switch is On (see Section 2-13). No weld output; wire does not feed. Replace building line fuse or reset circuit breaker if open (see Section 2-13). Reset circuit breaker CB1 (see Section 4-2). Secure gun trigger connections (see Section 2-6).
  • Page 30 Notes OM-198 683 Page 26...

  • Page 31: Section 5 - Electrical Diagram

    SECTION 5 – ELECTRICAL DIAGRAM 197 699-D Figure 5-1. Circuit Diagram OM-198 683 Page 27...

  • Page 32: Section 6 - Parts List

    SECTION 6 – PARTS LIST Hardware is common and not available unless listed. 802 059-B Figure 6-1. Main Assembly OM–198 683 Page 28...
  • Page 33 Item Dia. Part Mkgs. Description Quantity Figure 6-1. Main Assembly ....Fig 6-2 . . . BAFFLE, center w/components ........
  • Page 34 Hardware is common and not available unless listed. 802 060-C Figure 6-2. Baffle, Center w/Components OM–198 683 Page 30...
  • Page 35 Item Dia. Part Mkgs. Description Quantity Figure 6-2. Baffle, Center w/Components (Fig 6-1 Item 1) ....058 427 . . . RING, retaining spool ..........
  • Page 36 Ref. 800 792-B Figure 6-3. M-25 Gun OM–198 683 Page 32...
  • Page 37 Item Part Description Quantity Figure 6-3. M-25 Gun (Fig 6-1 Item 16 ) ..200 258 NOZZLE, slip type .500 orf flush ..........
  • Page 38 Item Dia. Part Mkgs. Description Quantity Figure 6-4. Panel, Front w/Components (Fig 6-1 Item 15) ....+196 798 PANEL, front control ..........
  • Page 39 Item Dia. Part Mkgs. Description Quantity Figure 6-5. Wire Drive And Gears (Fig 6-2 Item 26) ....602 009 . . . SCREW, .250-20 x 1.25 soc hd gr 8 .
  • Page 40 Table 6-1. Drive Roll And Wire Guide Kits Note Base selection of drive rolls upon the following recommended usages: V-Grooved rolls for hard wire. U-Grooved rolls for soft and soft shelled cored wires. U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types). V-Knurled rolls for hard shelled cored wires.
  • Page 41 Notes...
  • Page 42 Notes...
  • Page 43 Effective October 1, 1999 5/3/1 WARRANTY applies to all Handler 135 and 175 models, Airforce 250, 250A, and 375 Warranty Questions? models, and Champion 10,000 models.This warranty also applies to the Beta-Mig 1800, Champ Call 1435, 2060, 8500 models, Ironman 250, Stickmate models, Tigmate models, and HSW-15 and 1-877-HOBART1 HSW-25 spot welder models effective with Serial No.
  • Page 44 Welding Process Handbooks Call 1-877-Hobart1 Contact the Delivering Carrier for: File a claim for loss or damage during shipment. For assistance in filing or settling claims, contact your distributor and/or equipment manufacturer’s Transportation Department. PRINTED IN USA 2000 Hobart Welding Products. 1/00...

This manual is also suitable for:

M-25 gun

Table of Contents