Central Machinery 68147 Set Up And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Central Machinery Manuals
  4. Power Hammer
  5. 68147
  6. Set up and operating instructions manual

Central Machinery 68147 Set Up And Operating Instructions Manual

Electric hammer
Hide thumbs
Table of Contents

Advertisement

Quick Links

ELECTRIC HAMMER
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
Copyright
2010 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1‑800‑444‑3353.
Model
68147
®
. All rights reserved. No portion of this manual or any artwork

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 68147 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Central Machinery 68147

Summary of Contents for Central Machinery 68147

  • Page 1 Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

  • Page 2: Important Safety Information

    Unmodified plugs and matching outlets moderate injury. will reduce risk of electric shock. b. Do not expose power tools to rain or wet conditions. Water Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 68147...
  • Page 3 Power tools are dangerous in the hands of untrained users. SKU 68147 For technical questions, please call 1‑800‑444‑3353. Page 3...
  • Page 4 ″live″ and shock the operator. failure. In addition, people with Keep clear of moving parts. pacemakers should: • Avoid operating alone. Page 4 For technical questions, please call 1‑800‑444‑3353. SKU 68147...

  • Page 5: Vibration Safety

    It must be understood by the occurs, stop use immediately. operator that common sense and caution are factors which cannot SAVE THESE be built into this product, but must INSTRUCTIONS. be supplied by the operator. SKU 68147 For technical questions, please call 1‑800‑444‑3353. Page 5...

  • Page 6: Double Insulated Tools: Tools With Two Prong Plugs

    National Electrical Code. a qualified electrician before using it. Double insulated tools may be used in either of the 120 volt outlets shown in the Page 6 For technical questions, please call 1‑800‑444‑3353. SKU 68147...
  • Page 7 150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions n 0 xxxx/min. per Minute (RPM) SKU 68147 For technical questions, please call 1‑800‑444‑3353. Page 7...

  • Page 8: Specifications

    Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Page 8 For technical questions, please call 1‑800‑444‑3353. SKU 68147...

  • Page 9: Work Piece And Work Area Set Up

    Turn Lock Lever (74) 180° and slide out. Figure 3 Push the tip forcibly down in order to begin striking material. WARNING! Once activated, do not press, bear down or thrust forcibly SKU 68147 For technical questions, please call 1‑800‑444‑3353. Page 9...

  • Page 10: Maintenance And Servicing

    Examine the tool before each use. Make If abnormal noise or vibration sure the Chisel is sharp and not dull occurs, have the problem or cracked. Replace worn or broken corrected before further use. Page 10 For technical questions, please call 1‑800‑444‑3353. SKU 68147...

  • Page 11: Replacing Carbon Brushes

    Chisels with approved replacement Remove old Carbon Brush (6). Chisels from Harbor Freight Tools. Insert new Carbon Brush. Check that all mounting screws are Replace Carbon Brush Cap and slide tightened. Retighten any loose screws. Fan Cover back over Housing.

  • Page 12: Troubleshooting

    TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 12 For technical questions, please call 1‑800‑444‑3353. SKU 68147...

  • Page 13: Limited 90-Day Warranty

    LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This...

  • Page 14: Parts List

    Side Handle Shaft Locking Ring Tank Cover Wrench Side Handle Protector Small Ring Oil Bottle Side Handle Cap Shank Sleeve Fan Guide Flat Washer Ø8) O-Ring (Ø36XØ5.5) Spring Washer Ø8) O-Ring (Ø78XØ3) Page 14 For technical questions, please call 1‑800‑444‑3353. SKU 68147...

  • Page 15: Assembly Diagram

    ASSEMBLY DIAGRAM SKU 68147 For technical questions, please call 1‑800‑444‑3353. Page 15...

Table of Contents

Save PDF