Advertisement
Auto Planer
A s s e m b l y & O p e r a t i n g I n s t r u c t i o n s
Due to continuing improvements, actual product may differ slightly from the product described herein.
Visit our Web site at: http://www.harborfreight.com
©
Copyright
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
12-1/2"
Model 41831
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
1999 by Harbor Freight Tools
41831
41831
41831
41831
®
. All right reserved. No portion of this
Advertisement
Table of Contents
Related Manuals for Central Machinery 41831
Summary of Contents for Central Machinery 41831
- Page 1 1999 by Harbor Freight Tools . All right reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.
-
Page 2: Specifications
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Page 2 SKU # 41831... - Page 3 Inspect all hydraulic seals for leaks prior to use. Control handle and power switch must be kept clean, dry, and free from oil and grease at all times. Page 3 SKU # 41831...
- Page 4 Do not use the tool if any switch does not turn on and off properly. 17. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts intended for use with this tool. Replacement parts are available from Harbor Freight Tools. Use of any other parts will void the warranty.
-
Page 5: Installation
UNPACKING Remove protective crating and materials carefully. In the event of damage in transit, contact Harbor Freight Tools. Be sure you have all small parts accounted for before discarding packing materials. Check to be sure all parts are present. In addition to the planer, you should receive the accessories noted on page 2. -
Page 6: Completing Assembly
This will help prevent motor burn out in case the planer Fig. 4 Power Switch and jams, or there is a power surge through the power cord. Integral Circuit Breaker To reset, correct the error condition, and press the button back in. Page 6 SKU # 41831... -
Page 7: Operation
Use a wooden pusher tool to push the board through Fig 5. DO NOT Place Your Hand the planer. You can also grip the finished portion of the Inside the Extension Rollers workpiece, and pull it out of the planer. Page 7 SKU # 41831 REV 12/06... - Page 8 Anti-kickback devices are installed along the top edge of Figure 9. Boards Whose Grain Changes the front opening of the planer. Direction in the Middle. WARNING: Avoid kickback by never overloading the machine. Page 8 SKU # 41831...
-
Page 9: Maintenance
When the knife blade is properly adjusted, tighten the locking nuts (A) firmly to lock it in place. Be sure these nuts are on tight. Figure 11. Knife Blade Gauge Re-check to be sure the knife blade did not slip during tightening. Page 9 SKU # 41831... -
Page 10: Troubleshooting
Each brush has a max wear line marked on its side. When the brush has worn to the line, or if it is cracked or Figure 12. Checking and chipped, replace it. Be sure to replace carbon brushes in pairs. Replacing the Carbon Brushes Page 10 SKU # 41831... - Page 11 #41831 12-1/2” AUTO PLANER PARTS LIST, MAIN UNIT Please refer to Parts Diagram on Page 12 Description Quantity Description Quantity Washer , m6 Wood Screw Cap Screw, m6 x 12 Base Bracket Screw, m6 x 50 Cap Screw, m6 x 16...
- Page 12 #41831 12-1/2” AUTO PLANER PARTS DIAGRAM, MAIN UNIT Please refer to Parts List on Page 11 Page 12 SKU # 41831 REV 08/01...
- Page 13 #41831 12-1/2” AUTO PLANER, ADDITIONAL PARTS LIST Please refer to Parts Diagrams on Page 14 and 15 Description Quantity Description Quantity Motor Assembly Motor Housing Bearing, 60203ZZ Stator Cutter Head Washer, m5 Key, m5 x 5 x 20 Fan Casing...
- Page 14 #41831 12-1/2” AUTO PLANER PARTS DIAGRAM, MOTOR ASSEMBLY Please refer to Parts List on Page 13 Page 14 SKU # 41831 REV 08/01...
- Page 15 #41831 12-1/2” AUTO PLANER PARTS DIAGRAM, CUTTER ASSEMBLY Please refer to Parts List on Page 13 Page 15 SKU # 41831 REV 08/01...
Need help?
Do you have a question about the 41831 and is the answer not in the manual?
Questions and answers