Download Print this page

GE WSM2480 Installation Instructions Manual

24" (61 cm) gas washer/dryer
Hide thumbs Also See for WSM2480:

Advertisement

WSM2480
24" (61 CM) GAS WASHER/DRYER
INSTALLATION INSTRUCTIONS
Table
WASHER/DRYER SAFETY..............................I
INSTALLATIONINSTRUCTIONS....................3
Tools and Parts ............................................. 3
Alternate Parts............................................... 3
Location Requirements.................................3
Drain System ................................................. 4
ElectricalRequirements ................................5
Gas Supply Requirements ............................5
Venting Requirements................................... 6
Install Leveling Legs...................................... 7
of Contents
Remove Foam Packing.................................8
Connect Drain Hose...................................... 8
Connect Inlet Hoses......................................9
Secure Drain Hose........................................ 9
Plan Vent System ........................................ 1 0
Install Vent System...................................... 1 1
Level Washer/Dryer.....................................11
Make Gas Connection ................................11
Connect Vent .............................................. 1 1
Complete Installation .................................. 1 2
WASHER/DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow
instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
iMPORTANT SAFETY iNSTRUCTiONS
When discarding or storing your old clothes dryer, remove the door.
SAVE TH ESE iNSTRUCTiONS
8577220

Advertisement

loading

Summary of Contents for GE WSM2480

  • Page 1 WSM2480 24" (61 CM) GAS WASHER/DRYER INSTALLATION INSTRUCTIONS Table of Contents WASHER/DRYER SAFETY......I Remove Foam Packing.........8 Connect Drain Hose........8 INSTALLATIONINSTRUCTIONS....3 Tools and Parts ..........3 Connect Inlet Hoses........9 Alternate Parts..........3 Secure Drain Hose........9 Location Requirements.........3 Plan Vent System ........1 0 Drain System ..........
  • Page 2 WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury, or death. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
  • Page 3 INSTALLATIONINSTRUCTIONS , Rsds Gather the required tools and parts before starting installation. Your installation may require additional parts. For ordering Read and follow the instructions provided with any tools listed information, please refer to the Use and Care Guide. here. If You Have You Will Need to Buy Tools needed:.
  • Page 4 • Alevel floor w ithamaximum s lope of1"(2.5 cm) u nder e ntire • For closet installation, with a door, minimum ventilation washer/dryer. Clothes may nottumble p roperly and automatic openings in the top and bottom of the door are required. sensor cycles m ay notoperate c orrectly ifwasher/dryer isnot Louvered doors with equivalent ventilation openings are...
  • Page 5 • Do not have a fuse in the neutral or ground circuit. Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 34" (86.4 cm) above the floor GROUNDING iNSTRUCTiONS and no higher than 96"...
  • Page 6 LP gas conversion: Burner input requirements: Conversion must be made by a qualified technician. No attempt shall be made to convert the appliance from the gas Elevations up to 10,000 ft (3,048 m): specified on the model/serial rating plate for use with a different •...
  • Page 7 Exhaust • 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. Recommended hood styles are shown here. 4" (10.2cm) heavymetal exhaust vent Rigid metal vent (10.2cm) • For best drying performance, rigid metal vents are recommended. A. Louvered hood style •...
  • Page 8 2. Check adjustability of rear legs by pushing in one leg. The Squeeze ears of the silver, double-wire clamp with pliers to other leg should come out. Check both legs. If they do not open. Place clamp over the straight end of the drain hose move freely, repeat Step 1.
  • Page 9 NOTE: Do not overtighten or use tape or sealants on the valve, Damage to the valves can result. Insert anew flatwasher (supplied) intoeach end oftheinlet If you are working in a closet or recessed area hoses. Firmly s eat t hewashers inthecouplings. Move the washer/dryer into its final position and remove cardboard from under washer/dryer.
  • Page 10 Refer to the manufacturer's instructions provided with the vent system. Choose your exhaust installation type Recommended exhaust installations Typical installations vent the dryer from the rear of the washer/ dryer. Other installations are possible..t ..,,, ( • ..
  • Page 11 Determine vent length and elbows needed for best drying performance Remove the red cap from the flexible gas connector. • Use the Vent system chart below to determine type of vent Remove the _/2"NPT adapter from the flexible gas connector. (it will be necessary to use two adjustable wrenches).
  • Page 12 Check that all parts are now installed. If there is an extra part, 13. To test the dryer, set the dryer on a full heat cycle (not an air go back through the steps to see which step was skipped. cycle) for 20 minutes and start the dryer.