First Alert FE3A40GR User Manual

Heavy-Duty
Fire Extinguisher
Model FE3A10GR
M08-0158-001 M 10/05
IMPORTANT! Please read carefully and save.
This user's manual contains important information about your fire
extinguisher's operation. If you are installing this fire extinguisher for
use by others, you must leave this manual—or a copy of it—with the
end user.
Read extinguisher label and the entire user's manual carefully before
installing or using the unit. Make sure everyone in your household is
completely familiar with the operation of the extinguisher, and review
the instructions regularly. In an emergency, you will not have time to
read instructions.
© 2005 BRK Brands, Inc. All Rights Reserved.
First Alert ® , 3901 Liberty Street Road, Aurora, IL 60504-8122
Consumer Affairs: (800) 323-9005 • www.firstalert.com
Thank you for choosing First Alert ® for your fire extinguisher needs.
You have purchased a high quality fire extinguisher designed to
protect you and your family in case of a fire danger.
IMPORTANT INFORMATION ABOUT
FIRE EXTINGUISHERS
NOTE: Be sure the extinguisher is rated to fight the type of fire most
likely to occur in the area you choose to install it. Since household
fires commonly start in the kitchen, you should always install an
extinguisher in the kitchen. For added security, you should also install
additional extinguishers in utility areas, and other living areas in your
household.
Fire extinguishers are classified by fire type. The A, B and C
rating system defines the kinds of burning materials each fire
extinguisher is designed to fight. The numbers in front of the
A, B, or C indicate the rating for size of the fire the unit can
extinguish. Using the wrong type of fire extinguisher can do
more harm than good. Make sure you understand which fire
extinguisher to use on each class of fire!
Class A rating: The agent/powder is suitable for
fighting small fires involving wood, paper, cloth,
rubber, and some plastics.
Class B rating: The agent/powder is suitable for
fighting small fires involving grease, oil, gasoline,
kerosene, and other flammable liquids.
Class C rating: The agent/powder is suitable for
fighting small fires in "live" electrical equipment.
FE3A10GR is rated Class 3-A:10-B:C.
FE3A40GR is rated Class 3-A:40-B:C.
READ BEFORE INSTALLING OR USING
THIS FIRE EXTINGUISHER!
• This extinguisher is designed for use against small fires
that have just started and are small enough to fight safely.
It is not designed to fight large fires that are burning out of
control. If the fire is too hot or smoky for you to get within
10 feet (3 meters) of it, do not try to fight it yourself. Warn
everyone, evacuate the premises, and have someone call
the Fire Department from outside the building. Trying to fight
a large fire yourself can result in injury or death.
• Do not puncture or burn any fire extinguisher. The contents
are under pressure, and the extinguisher could explode.
• Never locate this extinguisher close to an engine, stove or
other source of heat. It is pressurized and could rupture or
explode if exposed to temperatures over 150° F (66° C).
• This extinguisher contains a dry powder extinguishing
agent. The agent/powder is nontoxic, but can irritate skin.
When using this unit, avoid breathing the powder. Always
ventilate the area after use.
User's Manual
Fire Extinguishers
Heavy-Duty Plus
Fire Extinguisher
Model FE3A40GR
Models FE3A10GR,
FE3A40GR
WHERE TO INSTALL THIS EXTINGUISHER
A Fire Extinguisher Should Be Mounted:
• In the vicinity of (but not on or in) a potential source of heat
and/or fire, like an oven or stove.
• Where it is easy to reach, near an exit or an escape route from
the room.
• In a location that is convenient, in plain sight, and 3-1/2 to 5
feet (1 to 1.5 meters) above the floor.
• Store the extinguisher high enough to keep it out of the reach
of small children.
• On a clean, dry surface where the temperature does not go
above 120° F (49° C) or below –40° F (–40° C).
HOW TO INSTALL THIS EXTINGUISHER
• Do not mount the extinguisher on drywall or plaster without
adequate support. Use strong screws or bolts to mount the
bracket securely into solid wood or metal that can support
it, like a wooden partition stud. Secure mounting is needed
so you can remove the extinguisher quickly and easily in an
emergency. Also, if the extinguisher is not held securely, it
could drop to the floor and injure people or damage the
extinguisher.
• Do not break the plastic loop holding the safety pin in place!
This loop prevents accidental discharge of the fire extin-
guisher. Break the loop only in an emergency before using
the fire extinguisher.
MOUNTING YOUR FIRE EXTINGUISHER
Parts of This
Fire Extinguisher
Lever
Safety
Pin
If your First Alert
1. Install the wall hook on a wooden stud or other solid surface that
will support the weight of the extinguisher using the screws or
bolts purchased. Since wall surface types vary, mounting screws
are not included. Purchase screws or bolts specifically designed
for the surface on which you will mount the fire extinguisher.
The fire extinguisher label lists its maximum weight.
2. After installing the wall hook, place the extinguisher on the hook
with the label facing outward, so the label can easily be read.
If your First Alert
1. Install the metal bracket on a wooden stud or other solid surface
that will support the weight of the extinguisher using the screws or
bolts purchased. Since wall surface types vary, mounting screws
are not included. Purchase screws or bolts specifically designed
for the surface on which you will mount the fire extinguisher.
The fire extinguisher label lists its maximum weight.
2. After installing the metal bracket, place the extinguisher on the
bracket with the label facing outward, so the label can easily be
read. Raise and wrap the bracket straps around the cylinder and
snap the buckle closed.
CHECKING AND INSPECTING THE
FIRE EXTINGUISHER
• DO NOT CHECK THE PRESSURE OR TEST THE FIRE
EXTINGUISHER BY SQUEEZING THE LEVER, EVEN BRIEFLY.
ONCE USED, IT WILL GRADUALLY LOSE PRESSURE AND
WILL NOT BE FULLY CHARGED FOR USE IN AN EMERGENCY.
• Only an authorized fire equipment dealer must refill this
extinguisher. The extinguisher must be refilled with the
same chemical that it contained when it was first purchased.
Improper filling can result in non-working or dangerous units.
1. Inspect the extinguisher once a week. Remove the extinguisher
from the mounting device and inspect the gauge. If the gauge pointer
is anywhere in the green band, the extinguisher is properly charged
and ready to use. If the gauge reads "RECHARGE," the extinguisher
has lost pressure and must be refilled.
2. Check for signs of damage or misuse. Make sure you can still
read all the text on the label. Carefully examine the surface of
the extinguisher for corrosion. You can help prevent corrosion
by cleaning the extinguisher if it gets wet or dirty. If you notice
corrosion during the warranty period, return the unit to First Alert
(see "Limited Warranty" at the end of this manual).
3. Make sure the tamper indicator ("safety seal") is still intact and
the nozzle is clean and unobstructed.
1
Wall Hook Mounting
Handle
Metal Bracket Mounting
Pressure
Gauge
® fire extinguisher came with a wall hook:
® fire extinguisher came with a metal bracket:
®
Continued...