Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kicker Solo X S10X
Summary of Contents for Kicker Solo X S10X
- Page 2 Thanks for buying KICKER. Enjoy! information and a copy of the receipt to KICKER to validate your warranty. Please read the special SoloX warranty page!
- Page 3 Features Locator Pin / Locator Hole The pin in the BAM along with the Titanium Deposit Impregnated Cone An Ultra High hole in the SPAIR allows the SPAIR to fit only one way into the Performance look that is more rigid for less cone flex and less BAM and is necessary to insure proper performance.
- Page 4 Wiring Dual 1 Ω = .5 Ω Load Parallel Wired Dual 2 Ω = 1 Ω Load The SoloX woofers are available with dual 2 Ohm or dual 1 Coil 1 Amplifer Ohm voice coils. The terminals without white dots are for voice Speaker Connection coile one.
- Page 5 Choosing and Building Enclosures page in the Tech Tips & FAQs The wood support inside your SoloX shipping carton can be section of the Support area on the Kicker website, used as a template for cutting the speaker mounting hole in the www.kicker.com.
- Page 6 These enclosure volume recommendations are for the For more enclosure choices see your local dealer or check out airspace inside the enclosure and include the displacement of our website www.kicker.com. the woofer. Do not make the airspace any greater than recommended.
-
Page 7: Vented Designs
*Actual quote from Jason Krim of Stereo-In-Dash located in Dayton, Ohio (Above tuning freq. only) (Authorized Kicker Dealer) when asked about the performance of SoloX drivers. No See below! life-altering contracts or big-money payouts were involved to use his awe-inspiring quote but we are sure he will be ‘down with it’... - Page 8 SPLAT are drilled and very, very, very bad things happening!! tapped to accept. For more advice on box building see your local Kicker dealer Up to 1 inch or the Choosing and Building Enclosures page in the Tech Tips &...
- Page 9 Mounting Now that you have opened the box and read 4. With the Gap Cap now “The Adventures of Sam Stikman” and decided on which installed remove the (4) Phillips 10 - 24 enclosure design to use, you may now remove the SoloX from Head Machine Screws that lock it’s box.
- Page 10 6. Once the holes are marked 9. With your assistant, remove template. Using a jigsaw insert the BAM and start the cut out the woofer hole and use a corner hardware. Now is the time you remove the 1/4” drill bit for the mounting 10 - 24 holes unidirectional bonding strip!
- Page 11 12. Insert the SPAIR back into the ATTENTION! Be careful not to BAM. damage the voice coil. Locator Hole Follow the pattern, hand tightening each, then go back Locator Pin on the BAM and and tighten using the same Locator Hole in the SPAIR must pattern.
- Page 12 Performance Model: S12X1 S12X2 S10X1 S10X2 Nominal Impedance ( fãéÉÇ~åÅÉ éÉê Åçá á ä ä ) SPL 1W/1M 87.69 87.55 85.64 85.65 Displacement, cc 5380 5380 5100 5100 Displacement, CuIn 328.32 328.32 311.04 311.04 Mounting Depth 8 9/16”...
- Page 13 * Service performed by anyone other than Kicker. International Warranty Contact your International Stillwater Designs (KICKER) dealer or distributor concerning specific procedures for your country’s warranty policies. mKlK _çñ QRV ≥ píáääï~íÉêI lâä~Üçã~ TQMTS ≥ rKpK^K ≥ QMR SOQJURNM KICKER drivers are capable of producing sound levels that can...
- Page 14 (Simple Pull Apart Insertable Replacement), so that when you find the breaking Special Note: OK that all sounds pretty black and white but we are KICKER point (and if you can still hear or feel) you can re-build it on the spot. If you read the big poster that came with your woofer (you did...right?) you know Sam &...
- Page 15 S tuff To Remember SoloX Subwoofers...
Need help?
Do you have a question about the Solo X S10X and is the answer not in the manual?
Questions and answers