Advertisement
Quick Links
Advertisement
Related Manuals for Goldmund REFERENCE II
Summary of Contents for Goldmund REFERENCE II
- Page 1 ASSEMBLY & USER MANUAL GOLDMUND REFERENCE II Turntable...
- Page 2 - networking and music distribution. The guiding principle at Goldmund is to produce a precise sound with the least possible loss of quality through the different stages. Goldmund will never adopt a technology before it is sufficiently developed to satisfy the high quality standards we set.
-
Page 3: Table Of Contents
Table of Contents UNPACKING CHOICE OF TURNTABLE LOCATION TURNTABLE ASSEMBLY AMPLIFIER CONTROLS USER INSTRUCTIONS CLEANING & MAINTENANCE GOLDMUND REFERENCE II - Assembly Manual - 3... - Page 4 OBSERVE GENERAL ELECTRICAL SAFETY PRECAUTIONS PARTICULARY WITH REGARD TO AVOIDING WATER, MOISTURE AND HEAT. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVERS AND REFER SERVICING TO QUALIFIED PERSONNEL. GOLDMUND REFERENCE II - Assembly Manual - 4...
-
Page 5: Unpacking
Solid coupling is essential, and if your support is standing on a suspended floor, at least one foot should be located over a supporting beam or close to a supporting wall for an optimal result. GOLDMUND REFERENCE II - Assembly Manual - 5... -
Page 6: Turntable Assembly
Mount the table top on the base with the control panel keyboard facing the front. Then, unscrew the cover hiding of the electronics cables below the table. Free the control panel cables from the base bottom and run all cables through base. GOLDMUND REFERENCE II - Assembly Manual - 6... - Page 7 Remove the 3 cylindrical weights sitting on top of the tripod feet. STEP 4 Box 3: Tripod Unscrew the tripod from its 3 feet. Keep the 3 screws that you will use back at the end of the assembly. GOLDMUND REFERENCE II - Assembly Manual - 7...
- Page 8 STEP 5 Box 3: Tripod Free the tripod assembly from the box and set it on 3 temporary supports like foam rubber or books, leaving the center free. GOLDMUND REFERENCE II - Assembly Manual - 8...
- Page 9 Please take one cylinder foot to position it at the front left position. Be carful to select the foot with the correct basis (check the bottom of the foot). Repeat the operation for the front right cylinder foot. GOLDMUND REFERENCE II - Assembly Manual - 9...
- Page 10 3 small golden insert 1 clamp 1 small oil bottle STEP 7 Box 4: Various Parts Take the large golden insert. STEP 8 Position it in the center of the third cylinder foot position. GOLDMUND REFERENCE II - Assembly Manual - 10...
- Page 11 Check if its design is the same as the one shown on the left picture. Position it in the bottom of the third cylinder foot position, passing the axe through the hole. The 3 cylinder feet are positioned. GOLDMUND REFERENCE II - Assembly Manual - 11...
- Page 12 STEP 10 Adjust the 3 springs: Turn the springs has shown. Too High Too low Correct position GOLDMUND REFERENCE II - Assembly Manual - 12...
- Page 13 Take 4 rubber seals and insert them in one of the 3 holes on the table: 4 rubber seals per hole. Repeat the operation for both other holes. STEP 12 When the seals are positioned, place 1 golden insert in the hole. Repeat the operation for both other holes. GOLDMUND REFERENCE II - Assembly Manual - 13...
- Page 14 Then the first person can mount the motor on the table, making each black serrated knurl facing its golden insert. ATTENTION: Please check the motor and the motor black knurl is in the same position as the one shown on the picture. GOLDMUND REFERENCE II - Assembly Manual - 14...
- Page 15 Take the tripod and mount it as shown on the left picture: The arm with the 4 small holes should be directing towards the rear foot of the turntable. BACK ATTENTION: Please check the tripod is well positioned. FRONT GOLDMUND REFERENCE II - Assembly Manual - 15...
- Page 16 Screw, but not over-tight, the tripod to the feet with the 3 screws dismounted at the beginning of the assembly (see STEP 4). STEP 16 Remove carefully the axis from the tripod. GOLDMUND REFERENCE II - Assembly Manual - 16...
- Page 17 Make the axis descend extremely slowly. STEP 19 Mount the belt around the axis wheel and the motor pulley as shown on the pictures. Check that the belt is flat against drive wheel and motor pulley. GOLDMUND REFERENCE II - Assembly Manual - 17...
- Page 18 Set the 3 large finish cylinders. Adjust height and lower the tripod assembly by turning the large adjustment cylinders. Level the tripod assembly using a bubble level. Repeat the operation if necessary. GOLDMUND REFERENCE II - Assembly Manual - 18...
- Page 19 Please remove the power supply from its box and position it nearby the turntable. Then take the connector cable and plug it to the power supply. Plug the second extremity to into the turntable right central foot base’s socket. GOLDMUND REFERENCE II - Assembly Manual - 19...
-
Page 20: Amplifier Controls
Up to three tone arms may be assembled on the turntable. Even if the Goldmund T8 tone arm is installed, two additional pivoting arms may be used. Goldmund provides upon request various basis for the most common tone arm lengths available. -
Page 21: User Instructions
We recommend leaving the turntable run for a few hours in order to stabilize its performance. Note: the bottom line of keys is dedicated to the Goldmund T8 tone arm use. (See separate user manual). GOLDMUND REFERENCE II - Assembly Manual - 21... -
Page 22: Cleaning & Maintenance
Goldmund equipment. RUNNING-IN TIME The Goldmund Reference II shaft and axis are machined with extreme precision. The optimal performance can only be reached after approximately 100 hours of use, despite the initial working period of 50 hours processed at the factory.