Related Manuals for STEELE PRODUCTS SP-LS22
Summary of Contents for STEELE PRODUCTS SP-LS22
- Page 1 Manual 22 Ton Spfitter WARNING! To Reduce The RiskOf Injury, User | MustRead And Understand Instruction Manual. FORSERVICECALL: SP-LS22 ..M.E,o_Z:888-896-6881...
- Page 2 WARNING Read this manual. Serious injury or death can result if safety instructions are not followed, Engine is shipped without oil. -Before starting engine, fillwith SAE 10W-30 motor oil. -See engine manual for engine oil capacity. Hydraulic reservoir is shipped with oil. -When adding oil, checkoi! level and make sure there is enough oil before you start the unit.
-
Page 3: Table Of Contents
TABLE OFCON EN S & Important Safety Rules ............& Machine C omponent Definitions ........... & Operation Instructions ............Proper Operation o ftheLogSplitter ......7 Horizontal a ndVertical O peratingModes *********************** Howto Splitthe logwithslantsurface ......& Maintenance andStorage ........... Troubleshooting ............. - Page 4 A IMPORTANT SAFETY RULES WARNING 1 .) Read this manual completely. Serious injury or death can result if safety instructions are not followed. Everyone who operates the log splitter must read and completely understand all safety rules, operating instructions, and maintenance instructions. You must be I6 or older to operate this machine.
-
Page 5: Important Safety Rules
I" IMPORTANT SAFETY RULES WARNING 6.) Risk of fire and explosion. Hot exhaust fumes from engine can cause fire. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. -Position muffler at least 7 feet from combustible objects. -Before adding fuel, stop the engine and keep heat, sparks, and flame away. -
Page 6: Machine Component Definitions
MACHINE COMPONENT DEFINITIONS 2" Coupler. Attaches the log splitter to your vehicle, Fits only 2" hitch balls. Hydraulic Cylinder. The hydraulic cylinder has a 4½" bore and a 23" stroke. It is rated to 3500 psi. Control Valve Handle, Use the control valve handle to move the wedge slide forward and backward. - Page 7 A OPERATION INSTRUCTIONS Proper Operation of the Log Splitter Load a log onto the beam and against the endplate. Serious accidents can happen when other people are allowed inside the work zone. Keep everyone else out of the work zone while operating control valve.
- Page 8 A OPERATION INSTRUCTIONS For Horizontal Using Rotate rear leg down and slide the lock pin Beam end handle For Vertical Using 1. Pulling beam lock pin 2. Lift the beam at the end side, and Rotate it up slowly Beam lock pin For Vehicle towing Press handle down and lock tightly...
-
Page 9: Operation Instructions
,& OPERATION INSTRUCTIONS HOW TO SPLIT A LOG WITH AN ANGLED EDGE... -
Page 10: Maintenance Andstorage
MAINTENANCE AND STORAGE Before performing maintenance, the !og splitter must be placed in maintenance mode. Turn off engine. Move the control valve handle forward and backward to relieve hydraulic pressure. After performing maintenance, make sure all guards, shields, and safety features are put back in place. -
Page 11: Troubleshooting
TROUBLESHOOTING Problem Cylinder rod will not move SOLUTION: A,D,E,H,J Slow cylinder rod speed when extending SOLUTION:A,B,C,H,I,K,L retracting Wood will not split or splits extremely slowly SOLUTION: A,B,C,F,I,K Engine bogs down during splitting SOLUTION: Engine stalls under low load condition SOLUTION: D,E,L,M Cause Solution... -
Page 12: Specifications
SPECIFICATIONS Maximum Pressure ....3500 psi Maximum Flow ...... 8 gpm Hydraulic Fluid Capacity ... 2.5 gallons or the level of the oil in the middle of oil window on oil tank. 10wt AW32, ASLE Hydraulic Fluid Type ....H-150, or ISO32 2"... - Page 13 ASSEMBLY Open Shipping Crate 1. Set the shipping crate on a solid, flat surface. 2. Carefully cut the shipping bands and remove lid of shipping crate. 3. Using two people to lift, carefully remove the engine, oil tank, wheels, tow bar, support legs, and hardware.
- Page 14 STEP 5: ATTACH HYDRAULIC CYLINDER STEP 7: ATTACH BALL COUPLER & LOG CRADLE CHAIN Assemble the Beam to the tow bar, secure with I. Attach the coupler (#28) to the tow bar by cotter pin O4x40 (#12) & hitch pin (#37). using hex bolt M12x80 (#43), fiat washer O12 (#3) and lock nut M12 (#67)_ 2_Attach two chains (#41) to the tow bar by using...
- Page 15 STEP 9: ATTACH HYDRAULIC HOSES 1. Thread the outlet connector (#59) to the top of the gear pump (#47). Use Teflon tape to ensure tight fit. Place an O ring (#61) onto the exposed threads of the outlet connector. Then attach hose (#13) to outlet connector.
- Page 16 7 18 25 26 73 96...
- Page 17 PARTS LIST Ref# Description Description I Beam Breather Cap ! BoltM12x55 Oil Tank Bolt M12x90 ..3..Flat Washer O12 Safety Chain with Hook Hex Thick Nut M12 I Wedge Slide Keeper Spacer Bolt M12x80 Keeper Plate Outlet oil tube assembly Lock Washer 024 Flat Washer 08 Flat Washer 024...
- Page 18 .Ref# Ref# Description Description Hex Bolt M6x20 "ValveB Joiner Lock Washer 06 O Ring 20x2.4 Front Cover Connector Flat Washer 06 Hex BoltM8x25 Clamp Screw M6xl0 Fiat Washer O10 Semicircular Key Oil Cup M6 Flat Key Axle Inside Bushing Oil Cap Bushing Big Flat Washer O10 Sponge PolyurethaneBlock...
Need help?
Do you have a question about the SP-LS22 and is the answer not in the manual?
Questions and answers