Advertisement
Quick Links
TECHNICAL SPECIFICATIONS
EMITTER
Frequency: 88.3 ± 0.5 MHz
Modulation: FM
Emission distance: 30 m.
Reception from any audio and visual equipment
with an audio out socket, such as TV, DVD, etc.
Power supply: 2 x AAA batteries or 4,5V DC
RECEIVER
Frequency range: 86-108 MHz
Reception mode: FM
Distortion: ≤ 0.2%
Power supply: 2 x AAA batteries
PARTS
Package includes
Emitter
Receiver (Headphone x 1)
Instruction manual
Audio Cable
Y adaptor cable
INSTALLATION
Installing the receiver:
Insert 2 AAA batteries into the battery compartment according to the + and – polarity.
Installing the emitter:
Insert 2 AAA batteries into the battery compartment according to the + and –
polarity, or insert the power adaptor into the power socket of the emitter (4.5V
DC). Insert the audio plug of the emitter into the AUDIO-OUT socket of the audio
source (TV, DVD, etc.) In case the audio out socket of the audio source is the
headphone socket. The Y adaptor cable can be used for connection. To achieve
the best reception spread out the emitter audio cable, which can be also used as
an antenna.
OPERATION
WIRELESS HEADPHONE
1. Insert the emitter audio cable into the AUDIO-OUT socket of the electrical
device or earphone socket, and move the function of the emitter to the
WIRELESS HEADPHONE position, and the power indicator of the emitter will
go on.
2. Turn ON the volume control and power button (ON/OFF) on the receiver; the
power indicator of the receiver will go on. First press the RESET key, and press
the SCAN key, the sound sent from emitter should be heard.
NOTES
To achieve the best reception spread out emitter audio cable of the
emitter (the emitter audio cable can also be used as an antenna)
If the sound is distorted or too strong, adjust the volume of the
signal source (TV, DVD, etc.) to a lower level and reception
performance may be improved.
Put TV on mute or quite mode so you can listen to TV without
disturbing any one.
Replace the batteries if you are having the following problems
1. The emitter indicator becomes dim
2. The receiver reception is poor
3. The volume becomes weak and the sound is distorted
WIRELESS NET AUDIO CHAT
1. Connect the emitter audio cable to the adaptor to the adaptor cable (fig. 2),
and insert the other end of the adaptor cable into the audio out socket of the PC,
then insert one end of the audio cable into the microphone socket (MIC) on the
emitter, and insert the other end into the microphone in socket of the PC.
2. Aim the microphone socket (MIC) of the emitter at you (fig. 3), and move the
power switch of the emitter to the AUDIO CHAT position, and the power
indicator will go on.
3. Turn on the volume control and power (ON/OFF) of the receiver and the
power indicator will go on. First press the RESET key, and then press the SCAN
key, and then the sound sent out from the emitter can be heard.
WIRELESS MONITORING
Place the emitter near the people you want monitored (such as elderly people,
children, etc.) and aim the microphone (MIC) towards the people. Move the
function switch of the emitter to the MONITOR position and the power indicator
will go on. Turn on the volume control and power button (ON/OFF) of the
receiver and the power indicator of the receiver will go on. Press the RESET
key and press the SCAN key, the sound sent out from emitter can be heard with
the headphone.
LISTENING TO THE RADIO
The receiver can be used separately as an FM radio. Press the SCAN key once,
and the receiver will automatically search toward a higher range and lock one
radio channel; when the highest range is reached, press the RESET key, and
the frequency returns to the lowest range. Press the SCAN key again, and the
receiver will search the radio channels from the low range again.
WIRED HEADPHONE
Insert one end of the audio cable into the audio socket of the receiver (fig. 4)
and insert the other end into the headphone socket of the electrical devices,
such as Mp3, DVD, etc. Then the unit can be used as a wired headphone.
TURNING OFF THE UNIT
When the unit is not used, move the function switch on the emitter to the OFF
position to turn off the emitter and turn the volume control receiver to the OFF
position, and the power indicator receiver will go out and the receiver will turn
off. Remove batteries when not using for a long time.
Operation manual
FUNCTIONS
A. RECEIVER
B. EMITTER
1. Battery compartment cover
7. Power indicator (front)
2. Volume control and power
8. Power and function switch
button (ON/OFF)
9. Microphone socket (MIC)
3. Scan key (SCAN)
10. Power socket
4. Reset key (RESET)
11. Microphone (MIC)
5. Power indicator
12. Audio cable of emitter
6. Audio socket
13. Battery compartment
cover (bottom)
Advertisement
