Franke FWD 1400-6EI User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

User manual

Washer-dryer

FWD 1400-6EI

Table of Contents

Need help?

Do you have a question about the FWD 1400-6EI and is the answer not in the manual?

Questions and answers

Summary of Contents for Franke FWD 1400-6EI

Page 1 User manual Washer-dryer FWD 1400-6EI...
Page 2: Table Of Contents
Contents Safety information Drying Programmes Product description Care and cleaning Control panel What to do if… First use Technical data Personalisation Consumption values Daily use Installation Use - Drying Building in Helpful hints and tips Electrical connection Drying Hints Environment concerns Washing programmes Subject to change without notice Safety information...
Page 3 • All packing and transit bolts must be re- • The users should always check that they moved before use. Serious damage can have not left their gas lighters (disposable occur to the product and to property if this or otherwise) in their clothing. is not adhered to.
Page 4: Product Description
• Make sure that children or pets do not To disable this device and restore the pos- climb into the drum. To prevent children sibility of closing the door, rotate the but- and pets becoming trapped inside the ton counterclockwise until the groove is drum the machine incorporates a special vertical.
Page 5 Detergent dispenser drawer Rating Plate Control panel Drain pump Door opening handle Adjustable feet Detergent dispenser drawer Compartment for detergent used for pre- wash and soak phase or for stain remover used during the stain action phase (if availa- ble). The prewash and soak detergent is added at the beginning of the wash pro- gramme.
Page 6: Control Panel
Control panel Below is a picture of the control panel. It shows the programme selector dial as well as the buttons, pilot light and the display. These are presented by relevant numbers on the following pages. Programme selector dial EASY IRON button SPIN reduction button Display OPTIONS button...
Page 7 Rinse hold a drying time from 10 minutes to 250 minutes (4.10). For Synthetics you can select a drying By selecting this function the water of the last time from 10 minutes to 130 minutes (2.10). rinse is not emptied out to prevent the fabrics Every time you press this button the drying from creasing.
Page 8: First Use
• Selected drying time • Incorrect option selection After selecting a drying programme, the If an option which is not compatible with drying time is displayed in minutes or in the set wash programme is selected, the hours and minutes (e.g. 130 mins = 2.10 ). message Err is displayed at the bottom of After the programme has started the time the display for a few seconds and the in-...
Page 9 Select the required programme by Measure out the detergent and the fab- turning the programme selector dial (1) ric softener Pull out the dispenser drawer until it stops. Turn the programme selector dial to the re- Measure out the amount of detergent re- quired programme.
Page 10 Select the available options by pressing The Delay Start can not be selected with buttons 3, 4 and 6 DRAIN programme. Depending on the programme, different Start the programme by pressing button functions can be combined. These must be selected after choosing the desired pro- To start the selected programme, press the gramme and before pressing button 8 .
Page 11: Use - Drying
Follow the below instructions to empty out not intend to carry out another wash, close the water: the water tap. Leave the door open to pre- 1. Turn the programme selector dial to O . vent the formation of mildew and unpleasant 2.
Page 12: Helpful Hints And Tips
It is possible to dry up to 4 kg of cotton The lowest values you can select are the items by pressing Drying Time button following: only (see the «Drying Programme » ta- – 900 r.p.m. for cottons and synthetic ble).
Page 13 Laundry weights acid; treat any residual marks on white fab- rics with bleach and then rinse thoroughly. The following weights are indicative: Tar stains: first treat with stain remover, me- The following weights are indicative: thylated spirits or benzine, then rub with de- bathrobe 1200 g tergent paste.
Page 14: Drying Hints
A water softener must be added when Degrees of water water has a medium-high degree of hardness Charac- hardness (from degree of hardness II). Level teristic German French Follow the manufacturer’s instructions. °dH °T.H. The quantity of detergent can then al- medium 8-14 16-25...
Page 15: Washing Programmes
duration drying time of the already performed Warning! Do not over dry the laundry cycles. in order to avoid creasing of fabrics or garment’s shrinking. Additional drying If the laundry is still damp at the end of the drying programme, select a short drying cy- cle again.
Page 16: Drying Programmes
Programme Maximum and Minimum Temperature Cycle Description Detergent Options Maximum Spin Speed Compartment Maximum Fabrics Load Type of Laundry HANDWASH SPIN 40°-Cold RINSE HOLD Main wash - Rinses Short spin at 900 rpm Max. load 2 kg Special programme for delicate fabrics with «hand washing»...
Page 17: Care And Cleaning
Suggested Degree of Drying Type of Fabric Max Load Spin Speed drying time in Mins Suitable for items to put Synthetics and 2 kg 100-110 away without ironing mixed fabrics 1 kg 60-70 Cotton and linen 4 kg 120-140 Suitable for ironing (sheets, tablecloths, 3 kg 1400...
Page 18 Door seal Check from time to time the door seal and eliminate eventual possible objects that could be trapped in the fold. Clean the chamber of dispenser drawer with a brush. Drain pump The pump should be inspected regularly and particularly if: •...
Page 19 5. When no more water comes out, un- 7. Put the cap back on the emergency emp- screw the pump cover ( A ) and remove tying hose and place the latter back in its it. Always keep a rag nearby to dry up seat.
Page 20: What To Do If
4. Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again. 5. When you intend to start the machine up again, make sure that the room temper- ature is above 0°C. Emergency emptying out If the water is not discharged, proceed as follows to empty out the machine:...
Page 21 Problem Possible cause/Solution The door has not been closed. E40 • Close the door firmly. The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. •...
Page 22 Problem Possible cause/Solution The programme is still running. • Wait the end of washing cycle. The door lock has not been released. The door will not open: • Wait for some minutes until the door lock is released. There is water in the drum. •...
Page 23: Technical Data
Mod..Prod. No..Ser. No..Technical data Dimensions Width 60 cm Height 82 cm Depth 54 cm Electrical connection Information on the electrical connection is given on the rating plate, Voltage - Overall power - Fuse on the inner edge of the appliance door.
Page 24: Installation
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. Installation Unpacking All transit bolts and packing must be re- moved before using the appliance.
Page 25 6. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. 5. Remove the bracket D and tighten up the six smaller bolts C . Positioning Install the machine on a flat hard floor.
Page 26 Caution! Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. After having levelled the appliance, tighten the lock nuts. 3. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.
Page 27: Building In
• In a sink drain pipe branch. This branch cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the must be above the trap so that the bend is at least 60 cm above the ground. drain pipe must be larger than the outside •...
Page 28: Electrical Connection
(6) (steel disk + rubber ring) into the inner side of the door. Its position must correspond to the magnet (4) on the appliance (see picture b) Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5-14 mm depending on the depth of door furniture) on the inner side of the door.
Page 29: Environment Concerns
Connect the machine to an earthed The power supply cable must be socket. easily accessible after installing the machine. The manufacturer does not accept any responsibility for damage or Should the appliance power supply injury through failure to comply with cable need to be replaced, this must the above safety precaution.
Page 32 Franke S.p.A via Pignolini, 2 37019 Peschiera del Garda (VR) www.franke.it 132955910 - 00 -182009...