Samsung HT-DB390 Instruction Manual page 9

t Connect your pair of
wireless rear speakers,
(L) and (R), to the
wireless rear amplifier.
Z
W reless Rear Spea_er (Lt
2 Insert the power plug into an outlet,
and then press the POWER button
on the front panel.
• 7he PowerStandbyindicatorwill lightup,
• 70 tam off the wirelessrearamplifier,
pressthe POWERbuttonJrlStandbylaode,
Wireless Rear Speaker (R)
[_Jllgtv]_
Back of Wire ess Rear Anplifier
• DOnot osfmect the wireless rear speakers
to the speaker outputs o_ the back of the
mair_unit, Malfunetior_may result.
• The wireless r_eivk_g a_ter_r_eis built into
the wireless rear amplifier.
Keep the unit away from water end
moisture.
• For optimal listening per_ormacee, make
sure that the area areur_d the proposed
wireless rear amplifier I_tion is clear of
any obstructio_rs,
Resetting Wireless Communication
Reset the system if a communication failure occurs or if the synchronizing signal indicator does not light up
and the "REAR CHK" message blinks on the main unit's display because the wireless rear amplifier is not
recognized. Reset the system while the main unit and the wireless rear amplifier (SWA-1000) are in Power
Standby mode.
1
With the main unit turned off, press and
hold the remote control's WIRELESS for
4 seconds.
• Press the button until the volume control indicator
lights up blue. (The indicator wilt turn off in 1 second.)
2 With the wireless rear amplifier turned
on, use a ball point pen or a pair of
tweezers to press the RESET button
on the back of the unit 2 to 3 times.
3
Turn on the main unit.
• The wireless rear amplifier's synchronizing signal
indicator witt light up,
• If Power Standby mode continues, repeat Steps 1
to 3 above,
Rack o_W reless Rear Arnpl tier
m
• Souredwill be heard from the wireless rear speakers in
DVD 5.1-CH or Dolby Pro Logic II mode only.
• ]r_2-OH mode, r_osouredwill be heard from tile wireless
rear speakers,
Connect the wireless
transmission antenna to
the back of the main unit
and tighten the nut by
hand,
2 Raise the wireless
transmission antenna a
full 90 degrees,
• Do r_otapply a strong shock to the
wireless traosmissios antenna,
Breakage may result,
• Do r_ottouch the wireless
tra_smissior_ antenna duriog
operatio_. Noise or ir_terference to
communicatiof_s may result,
Turning On the Mood Light
You can turn on or off the mood light on the wireless rear amplifier as well as change the color of the light to one of
the 7 different colors according to your preference or your room atmosphere.
1
Press the POWER button.
2
Press the COLOR MODE button.
• The Power Standby indicator on the • Each time the button is pressed, the color changes as
front panel will light up and the follows: Blue -_ Light Green _ R_I _ Sky Blue -_
mood light will turn on. Yellow -_ PI_ _ White,
15
• Place the wireless roar amplifier at the rear of the listeniog position. If the wireless rear
amplifier is too close to the main u_it_ seine sou_d i_terruptios [nay be bea_ due to
interfere_ce,
• If you use e device such as a [nicrowave overL wireless LAN Card, Bluetooth equip[nellt,
or any o{ber device that uses the same frequency (2,4GBz) r_eerthe systerrl_seine sou_d
interruption [nay be beard due to ir_terference.
• The tra[_smissior_ distar_ceof radio wave is about 33 f_t b_ rosy vary deper_ding on your
operathg er_viro_[ne_t. If a steePconcrete wall or metallic wall is between the main unit
arid the wireless roar amplifier, the system may _ot operate at ell because the radio wave
carcanet penetrate metak
ning Off the Mood Light
• tn Power Standby mode, press the ONfOFF button,
Only the mood light can be turned on or off. The mood light will light up or turn off with the
last color selected.
• Press the POWER button.
The wireless rear amplifier and the mood light wilt turn off.
If the POWER button is pressed again, the mood light witi always light up blue,
16