Husqvarna LGT2554 Owner's Manual
Hide thumbs Also See for LGT2554:
Table of Contents

Advertisement

Quick Links

®
Owner's
Manual
532 43 00-01

Advertisement

Table of Contents
loading

Summary of Contents for Husqvarna LGT2554

  • Page 1 ® Owner's Manual 532 43 00-01...
  • Page 2 SAFETY RULES Safe Operation Practices for Ride=On Mowers DANGER: THiS CUTTING MACHINE iS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY iNSTRUCTiONS COULD RESULT iN SERIOUS iNJURY OR DEATH. • Do not operate machine without the entire grass catcher, WARNING: in order to prevent ac= discharge guard, or other safety devices in place and...
  • Page 3 SAFETY RULES Safe Operation Practices for Ride=On Mowers ill. CHILDREN GENERAL SERVICE Tragic accidents can occur if the operator is not alert to Never operate machine in a closed area. the presence of children. Children are often attracted to Keep all nuts and bolts tight to be sure the equipment is in safe working condition.
  • Page 4 PRODUCT SPECiFiCATiONS CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. Gasoline Capacity 4 Gallons and type: Unleaded Regular • Follow a regular schedule in maintaining, caring for and using your tractor. Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) •...
  • Page 5 UNASSEMBLED PARTS Mower Front Wheel Mower (5) Large Retainer Springs - 7/16 (1) 3/40.D. Washers (1) Wheel (1) 1-1/40.D. Washer (2) Smaller Retainer Springs - 5/16 (1) Locknut (1) Shoulder Bolt 3/8-16 (3) 1-3/16 O.D. Washers (1) Anti-Sway Slope Sheet (1) Oil Drain Tube For Future Use (2) Rear _...
  • Page 6 ASSEMBLY TO ADJUST SEAT (See Fig. 2): TO INSTALL MOWER (See Figs. 4-12) • Grasp adjustment handle(A) and pull up, slide seat to Be sure tractor is on level surface and engage parking brake. desired position and release adjustment handle. •...
  • Page 7 ASSEMBLY • Pivot bar towards you and insert other end of bar into hole in rear mower bracket (D). Move mower as needed to insert bar. • Secure with washer and retainer spring as shown Fig. 8 • ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring.
  • Page 8 ASSEMBLY CHECKFOR PROPER POSITION OFALLBELTS Turn steering wheel to position wheels straightforward. ATTACH FRONT LINK (E) - Work from left side of trac- See the figures that are shown for replacing motion and tor. Insert rod end of link assembly through front hole mower blade drive belts in the Service and Adjustments sec- in tractor front suspension bracket (F) and secure with tion of this manual.
  • Page 9 OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. I",l CHOKE FAST SLOW REVERSE NEUTRAL HiGH IGNITION SWITCH ENGINE OFF REVERSE ENGINE ON ENGINE START PARKING BRAKE MOWER HEIGHT MOWER LIFT OPERATION...
  • Page 10 OPERATION KNOW YOUR TRACTOR READ THiS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Fig. 13 Our tractors conform to the applicable safety standards of the American National Standards Institute.
  • Page 11 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.
  • Page 12 OPERATION TO MOVE FORWARD AND BACKWARD TO ADJUST GAUGE WHEELS (See Fig. 19) (See Fig. 17) Gauge wheels are properly adjusted when they are slightly offthe ground when mower is atthe desired cutting height in The direction and speed of movement is controlled by the operating position.
  • Page 13 OPERATION REVERSE OPERATION SYSTEM (ROS) TO TRANSPORT (See Fig. 13 and 22) Fig. 21) (See When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling Your tractor is equipped with a Reverse Operation System position.
  • Page 14 OPERATION BEFORE STARTING THE ENGINE TO START ENGINE (See Fig. 13) When starting the engine for the first time or if the engine CHECK ENGINE OiL LEVEL has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.
  • Page 15 OPERATION PURGE TRANSMISSION MOWING TIPS • Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in CAUTION: Never engage or disengage the Service and Adjustments section of this manual. freewheel lever whilethe engine is running. •...
  • Page 16 MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE MAINTENANCE EACH SEASON STORAGE SCHEDULE HOURS HOURS HOURS HOURS v" Check Brake Operation v" Check Tire Pressure v" Check Operator Presence & ROS Systems v" v" Check for Loose Fasteners Check/Replace Mower Blades v"...
  • Page 17 MAINTENANCE BLADE CARE TRACTOR For best results mower blades must be kept sharp. Replace Always observe safety rules when performing maintenance. bent or damaged blades. BRAKE OPERATION proved by the manufacturer of your tractor. If tractor requires more than five (5) feet to stop at highest Using a blade not approved by the manu= AUTION: Use only a replacement blade ap-...
  • Page 18 MAINTENANCE TRANSAXLE MAINTENANCE OIL DRAIN VALVE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine CLOSED AND is running or while the transmission is hot. To prevent pos- LOCKED sible damage to seals, do not use high pressure water or POSITION...
  • Page 19 MAINTENANCE DECK WASHOUT PORT (See Fig. 29) IN-LINE FUEL FILTER (See Fig. 27) Your tractor's deck is equipped with a washout port on The fuel filter should be replaced once each season. If fuel its surface as part of its deck wash system. It should be filter becomes clogged, obstructing fuel flow to carburetor, utilized after each use.
  • Page 20 SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS iNJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: Depress brake pedal fully and set parking brake. Place motion control lever in neutral position. Place attachment clutch in "DISENGAGED" position. Turn ignition key to "STOP" and remove key. Make sure the blades and all moving parts have completely stopped.
  • Page 21 SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see steps in Visual Adjust- ment instructions above. Make sure tires are properly inflated to the PSI shown on • Recheck measurements, adjust if necessary until both tires. If tires are over or under inflated, it may affect the sides are equal.
  • Page 22 SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT TO CHECK BRAKE (See Fig. 36) If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved Park the tractor on level surface. Engage parking brake. surface, then brake must be serviced.
  • Page 23 SERVICE AND ADJUSTMENTS TRANSAXLE MOTION CONTROL LEVER TO START ENGINE WiTH A WEAK BATTERY (See Fig. NEUTRAL ADJUSTMENT Fig. 38) (See The motion control lever has been preset at the factory and adjustment should not be necessary. crate explosive gases. Keep sparks, •...
  • Page 24 SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBLY REPLACING BATTERY (See Fig. 40) (See Fig. 41) WARNING: Do not short battery termi= • Raise hood. nals by allowing a wrench or any other • Unsnap headlight wire connector. object to contact both terminals at the •...
  • Page 25 STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANTTO PREVENTGUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH gasoline in the tank inside a building AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK...
  • Page 26 BLESHOOTING POINTS PROBLEM CAUSE CORRECTION Out of fuel. Fill fuel tank. Will not start Engine not "CHOKED" properly. See "TO START ENGINE" in Operation section. Engine flooded. 3. Wait several minutes before attempting to start. Bad spark plug. Replace spark plug. Dirty air filter.
  • Page 27 TROU OOTI G POI PROBLEM CAUSE CORRECTION Engine continues Faulty operator-safety presence control Check wiring, switches and connections. If not corrected, contact an authorized service center/ system. to run when oper= department. ator leaves seat with attachment clutch engaged 1. Worn, bent or loose blade. Replace blade.
  • Page 28 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 DECALS PART PART DESCRIPTION DESCRIPTION 532 41 91-38 Decal 532 42 38-29 Decal, Warning Customer Resp. Warning 532 42 38-30 Decal Ethanol E85 532 42 47-89 Decal, Hood Logo 532 19 15-54 Decal Fender...
  • Page 29 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 SCHEMATIC SCHI2 ;ill; BATTERY SOLENOID STARTER <g. AMMETER FUSE I (7[_ BLACK (OPTIONAL) ELECTRIC CLUTCH PTO SWITCH WHITE WHITE (DISENGAGED) ,H..ICLUTCH,BRAKE q L_(PEDAL UP) I REVERSE SWITCH (NOT IN REVERSE) BLACK BLA(K BLA(K...
  • Page 30 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 ELECTRICAL T07S With 12V Outlet Option 103..With Service Minder Option...
  • Page 31 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 ELECTRICAL PART DESCRIPTION 532 16 34-65 Battery 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 532 18 64-91 Battery Box 532 17 61-38 Switch Interlock 532 18 37-59 Harness Socket Light 532 00 41-52 Bulb, Light #1156...
  • Page 32 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 CHASSIS 204\ _2tO 130_ 170 " i213 _235 .194 chassis-tex TEX GT HUSQ 65 rl...
  • Page 33 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 CHASSIS PART PART DESCRIPTION DESCRIPTION 532 40 50-12 Logo 532 40 30-48 Vent Side Hood RH 532 40 87-01 Dash 532 40 30-76 Vent Side Hood LH 532 41 10-46 Hood Asm.
  • Page 34 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 DRIVE /125 .205 drive-tex_K46 fender_6_rl...
  • Page 35 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 DRIVE PART PART DESCRIPTION DESCRIPTION Transaxle, TUFFTORQ K46 AW 532 40 52-57 Latch Brake Parking (Internal parts not available) 532 41 34-30 Keeper Belt Centerspan Nut Push 5321862-11 5321972-89 532 19 98-44 HubAsm.WheelRear22"TXGT.06 532 40 62-08...
  • Page 36 TRACTOR - MODEL NO. LGT2554 PRODUCT 960 45 00-15 (96045001502), ENGINE - 37 SPARK ARRESTER engine-tex_Kohl PART PART DESCRIPTION DESCRIPTION 532 14 66-29 Shield Heat Muffler Engine Kohl Model No. SV730-0034 Muffler 532 18 60-54 Gasket 532 14 97-23 532 14 66-99 Tube Exhaust LH 532 19 43-20 Keeper Belt Engine...
  • Page 37 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 SEAT ASSEMBLY seat-tex 6.5SL PART PART DESCRiPTiON DESCRIPTION Seat 532 42 40-68 873 80 05-00 Nut, Lock 5/18-18 unc Handle Slide Seat Bracket Pivot Fender 532 19 76-81 532 18 01-68 532 14 08-75 532 19 82-00 Spring Latch Seat...
  • Page 38 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 STEERING ASSEMBLY "\ steering-tex HUSQSR...
  • Page 39 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 STEERING ASSEMBLY PART DESCRIPTION 532 41 64-80 Wheel, Steering 532 19 59-88 Axle Asm., Front 532 40 30-89 Spindle Asm., LH 532 40 30-90 Spindle Asm., RH 532 12 49-31 Bearing, Race Thrust Harden 532 12 17-48 Washer...
  • Page 40 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 MOWER DECK mower_deck 54-tex_16...
  • Page 41 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 MOWER DECK PART PART DESCRIPTION DESCRIPTION 532 40 31-25 Deck Weldment Mower 532 18 73-42 Baffle Right 532 19 60-66 Cover Mandrel LH 532 18 73-44 Baffle Left 532 19 71-81 Cover Mandrel RH 532 18 76-07 Baffle Center...
  • Page 42 TRACTOR - MODEL NO. LGT2554 (96045001502), PRODUCT NO. 960 45 00-15 MOWER LiFT PART PART DESCRIPTION DESCRIPTION 532 42 20-27 Shaft Asm., Lift 532 19 42-08 Pin Cotter 5/16 Bow Tie Lock 532 19 52-30 Lever Asm., Lift RH 532 40 34-07 Link Lift Susp Mower Rear 532 41 15-55 Grip, Lever...
  • Page 43 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. down the face of slopes, never across the face. Do not mow ARNING: To avoid serious injury, operate your tractor up and slopes greater...
  • Page 44 Husqvama XP 2 cycle oil. not be used, but delivered as is to an authorized Husqvarna retailer for evaluation. Proof of purchase, as explained in 90 Day Commercial Warranty: Automatic mower, chain saws, 100 series trimmers, power cutters, stump grinders, pole section 6, rests solely with the customer.

Table of Contents