Danby DKC644BLS Owner's Manual

Keg cooler

Hide thumbs Also See for DKC644BLS:

Owner's manual (21 pages)

Table Of Contents

Quick Links

Danby

OWNER'S MANUAL

GUIDE D'UTILISATION

MANUAL DEL

PROPIETARIO

Model. ModUle, Modelo

DKCG44BLS

CAUTION:

Read and follow all safety rules

and operating instructions

before first use of this product.

PRECAUTION:

Veuillez life attentivement les

consignesde s_curit_ et les

instructionsd'utilisation avant

I'utilisation initiale de ce

produit.

PRECAUClON:

Lea y observe todas las

reglas de seguridad y las

instruccionesde operaci6n

antes de usar este producto

pot primera vez.

Danby

Chil!'n

Keg Cooler

Owners IVlanual

Table of Contents ........................

Glaciate de blare pression

Guide d'utilisation

Table des mati_res

.......................

Barrii Refrigerador

IVlanual del propietario

Tabla de Contenido ...........................

DanbyProductsLimited,Guelph,Ontario Canada N1H 6Z9

Danby ProductsInc., Findlay,Ohio USA 45840

DKC644BLs.09.21.04.

Rev 10/05

Table of Contents

Need help?

Do you have a question about the DKC644BLS and is the answer not in the manual?

Questions and answers

Summary of Contents for Danby DKC644BLS

Page 1 Lea y observe todas las Table des mati_res ....... reglas de seguridad y las instruccionesde operaci6n antes de usar este producto pot primera vez. Barrii Refrigerador IVlanual del propietario Tabla de Contenido ......DanbyProductsLimited,Guelph,Ontario Canada N1H6Z9 Danby ProductsInc., Findlay,Ohio USA 45840 DKC644BLs.09.21.04. Rev 10/05...
Page 2 Welcome to the You'll see it in this Best of all, you'll Danby family. We're easy-to-use manual experience these proud of our quality and you'll hear it in values each time you products and we the friendly voices of use your Keg Cooler.
Page 3: Table Of Contents
Important Safety Information Grounding Instructions Warning C0 2 Can be Dangerous[ Safety Precautions Don't Wait Do This Now[ Important Notice Featu res Knowing your Keg Cooler Chill 'N Tap Accessories Capacity Setting Up Your _ap Before putting your appliance into use Disposal of Packaging Location Assembly...
Page 4: Grounding Instructions
READ SAFETY INFORMATION BEFORE USING This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. FOR YOUR This appliance is equipped with a power cord having an equipment grounding conductor and grounding plug.
Page 5 Be careful not to damage any of the refrigeration lines of the appliance. Beer is easily available with Danby's new Keg Cooler, however, it is not intended to be available to people under the legal age to consume beer.
Page 6 1 Black 7 IntakelExhaust 4 Worktop & Chrome Rail (for condenser fan) Dispense Tower 8 Leveling legs or 5 Electronic 2 Dispenser optional Swivel Faucet & Handle Controls/Display Castors (included) 6 Stainless Steel 3 Plastic Drip Tray Door...
Page 7 CHILL 'N TAP ACCESSORIES 2 Chrome Rails (for attachment to Work top) 6 Self-Tapping Screws (to attach chrome rails) 1 CO 2 Cylinder Support Stand 1 CO 2 Cylinder (empty) 1 CO 2 Regulator (high/low pressure gauges) 1 CO 2 Air Line Hose 2 CO 2 Air Line Hose Connectors 1 CO 2 Air line hose plug (located exterior rear cabinet) 1 Beer Keg Coupler...
Page 8: Capacity
CAPACITY There are three (3) standard size beer kegs that can be used in your Chili 'N Tap Keg Cooler; 1/2 Barrel: 58.5 Liter Keg (15.5 Gal) Yields: 7 cases (1984ozs) of beer Keg Weight: 1701bs Full (approx.) 1/4 Barrel: 30 Liter Keg (775 Gal) Yields: 3-1/2 cases (992ozs) of beer...
Page 9 Before putting appliance into use... If the appliance has recently been transported or tipped, before connecting the appliance to any electrical power supply, leave it standing (upright) for about 1 hour. This will reduce the possibility of malfunctions in the cooling system due to transport handling. Clean the appliance thoroughly, both interior and exterior.
Page 10: Important Notice
1. Un-instafl Work top: Using a Phillips Screwdriver, remove the three screws located at the rear (back) side of the Work top. See Fig's. 1 & 2 Lift the Work top from the rear, titling towards the front of the cabinet. Pleasenote: Do not attempt to completely seperate the work top from the cabinet, as this can lead to damage or disconnection...
Page 11: Assembly Instructions
ASSEMBLY INSTRUCTIONS (CONT'D) 11. Protective Plate (Pro=installed): To prevent Installation of C02 Air Line Hose to Regulator: unnecessary damage (marring) to the floor of Attach one end of the (red) air line hose to the the refrigerator cabinet, the protective plate hose barb connection on the CO 2 regulator.
Page 12 ASSEMBLY INSTRUCTIONS (CONT'D) 18. Opening 14. Installation of the Keg Coupler: IMPORTANT the CO 2 Cylinder Main Valve: Before NOTICE; Make sure the pull handle of the opening the main valve located on top of the CO 2 keg coupler is in the "upward" (closed) position cylinder.
Page 13: Location
Re-install the Unscrew the upper door hinge intake/exhaust vent. pin from the right side of the worktop and install it on the left side of the worktop. Fig. B Lower Door Position the main door back on 1. Lay the unit on it's back. Hinge the cabinet and push up until the 2.
Page 14: Electronic Controls
Electronic Controls Adjusting the temperature; • Press either,4_Vbutton once and release to enter the 'SET' mode. The LED display will begin to flash and show the previous temperature setting TEMPERATURE iNCREASE - signifying the temperature is ready to be adjusted. TEMPERATURE DECREASE * Each depression of the,_lk, orV...
Page 15 Close the main cylinder valve (A) by turning in a Readjust regulator pressure (D) (if necessary) clockwise direction. See Fig.12 between 10 - 12 psi/Ibs. Close the secondary shut-off valve (C) by 10. Open the secondary shut-off valve (C)by turning turning to "horizontal"...
Page 16 1. Rinse a "Beer Clean" glass under cold water. 2. Place glass beneath tap, and tilt at a 45 ° angle. (as shown in Fig. 13) Leaving approximately 1/4" between glass and faucet. 3. Fully draw the dispenser handle and fiii the glass to 2/3 fuji.
Page 17 A standard cleaning kit will perform approximately eight (8) scheduled line cleanings. Line cleaning kits are readily available and can be purchased through our after sales service department. For more information please call 1-800 26-DANBY (1-800-263-2629)
Page 18 Maintain strict sanitary conditions in the glass washing area. Never wash glassware with utensils or dishes used to serve food. Food particles and/or residue can effect the quality/taste of draught beer. Regular dish detergents are fat-based and will leave a slight oily film on the glass, which will cause the beer to go flat quickly.
Page 19: Using Proper Draw Technique
TROUBLESHOOTING Problem Possible Causes What To Do Excess formation Recent keg agitation If the keg has recently been moved (transported), you foam 'head'. should let it stand for a minimum of two (2) hours before tapping. Improper regulator Verify that the 'LOW' side (CO2) pressure is reading setting between 10 ~ 12 p.s.i.
Page 20 TROUBLESHOOTING (Cont'd) Problem Possible Causes What To Do Sputtering draw Dispense system See "Cleaning and Maintenance" on pg. 17-18 requires cleaning. Keg Coupler installed Check seal between keg & faucet incorrectly Line or dispenser Verify that there are no 'kinks' or obstructions in either obstructions, the air line (red) or dispenser line (clear) and that neither are frozen.
Page 21 Siempre, al solicitar servicio de mantenimiento o hacer un pedido de repuestos, debe suministrar la siguiente informaci6n: Tipo de artefacto Numero de modelo Descripci6n del repuesto Danby ProductsLimited,Guelph,Ontario Canada N1H6Z9 Danby ProductsInc., Findlay,Ohio USA 45840 Printed in China (RR.C.) Imprirn6 en Chine (R.RC.) Impresso en China (R.RC.)

Danby DKC644BLS Owner's Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Danby DKC644BLS

Summary of Contents for Danby DKC644BLS