Download Print this page

GT 1228 Operating instructions and parts manualvice Operating Instructions Manual

Advertisement

Quick Links

SELF-PROPELLED
~ ~ ~
~
I
I,
06//-b3S
~~~
WARRANTY
The manufacturer
v.1:Irrants this snow blower
to the original
purchaser
to be free of defects
in material
and v.1:Irkmanship
for one snow season (or 30 days where
used for commercial
purposes) and will
repair
or replace,
without
charge,
any
defective
part or parts approved
by George
Garden
Tool Division.
Warranty
claim
must be processed
at any Factory
Authorized
Service
Dealer.
This warranty
is applicable
only
to manufacturing
defects
and does not cover routine
.servicing
and maintenance
as described
in the instruction
manual.
If it is necessary
for the servicing
dealer
to transport
..the
snaw blower
for warranty
repa ir,
such transportation
charges
are to be po id by the purchaser.
The v.1:Irranty card furnished
with
the snow blower
must be filled
in by the customer
and returned
to the dealer.
Fail ure
to do so voids all
v.1:Irranty claims.
All
claimes
must be accompanied
by written
description
outlining
the defect,
cause of failure,
and date.
Defective
parts must be returned
to the manufacturer
postage
pre-pa
id with
the v.1:Irranty cia im and if approved
will
be replaced
without
charge.
~
NOTE:
The engine
v.1:Irranty is covered
by the engine
manufacturer.
~
This v.1:Irranty
is in I ieu of all
other
warranties
expressed
or impl ied.
~
&J?1~~t:~./~ d/~-~
(~u:Z;;~gj:::z.:c-.
HEAVY
DUTY
POWER
SNOW
REMOVER
;..
OPERATING INSTRUCTIONS AND SERVICE MANUAL
.'
~~
~
-SNOW
BLOWER
MODEL 1265
(
r
)---""
/
~/
I
(-
r
\
(
=-
"'
\
"""
.)'
;2. Y
,;Z to ~ -;;L-
-

Advertisement

loading
Need help?

Need help?

Do you have a question about the 1228 Operating instructions and parts manualvice and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GT 1228 Operating instructions and parts manualvice

  • Page 1 HEAVY DUTY POWER SNOW REMOVER OPERATING INSTRUCTIONS AND SERVICE MANUAL -SNOW BLOWER MODEL 1265 )---"" "' """ 06//-b3S WARRANTY The manufacturer v.1:Irrants this snow blower to the original purchaser to be free of defects in material and v.1:Irkmanship for one snow season (or 30 days where used for commercial purposes) and will repair...
  • Page 2 PAGE PAGE Snowblower and Model 265-2 ,-over Transmission Unit Parts Diagram..2 Table of Contents. .. Parts List. Section I, Assembly Instructions for Models 228 and 265-2 2,3,4 Parts List (con't), Continuation of Operating Instructions. Section II, Pre-Starting Instructions. Section V f Lubrication. Section III, Rules for Safe Operation.
  • Page 3 Figure 3 Figure 5 Assemble the handle panel assembly over the right and left Attach the master clutch rad into the hale in th~ clutch handle located on the handle panel and into the hale in the handle tubes and secure with four slotted round head bolts clutch lock aut assembly.
  • Page 4 SECTION II PRE. STARTING INSTRUCTIONS Fill the fuel tank with a good grade of regular gaso- line. See Figure 1. Do not mix oil with gasoline. Make certain the fuel valve under the gas tank is turned on. Fill the crank case with ail to the full mark an the dip stick.
  • Page 5 SELECTION ON MODEL 265-2 SNOW BLOWER INSTRUCTIONS This model is equipped with a tv.\:> speed transmission which moy be shifted by the speed selector control (See Figure 9). Shifting of the tronsmission is best accompl ished with the It is important to became familiar...
  • Page 7 1-""--8 143~ ~~, "'8 "' ~~~ ~~l ~ ~~;;$ /0' /11' \1r ~ ~~=~~~---<§ ~~~~~~ 8 " "D ".. "'W ~~~~~: \~-7-- ..-~ -~~~ @'(§) < "@~( (i5) 1,--':4"2' 150 153] :: § .:~~--:::~~ --:-\t-- - f--t48\e ~~--::::~.e f ~~ ~-;T- "@ "-...
  • Page 8 LIST PARTS Part Ref. aly. Ref. Port aty. Gty. 02282652 Description 02282652 Description Baffle 21272 Thumb Bolt 5/16 x 3/4 (Pltd.) 40441 20185 Boffle Belt Guard 61758 Carriage Bolt 5/16 xl Sh. Sq. 40100 Belt Guard t.'.)unt 61449 Neck (Pltd.) Belt Guard t.'.)unt Bond 21668 60044...
  • Page 9 LIST PARTS Ref. Ref. Port Oty. Oty. Part' Oty. Oty. 0228 2652 0228 2652 Description Description Gear Housing Lid 40185 Spring Pin 1/8 x 3/8 40250 40480 Clutch Scissor Link Special Bolt 1-1/4 (Pltd.) 20097 Right Hand Clutch Yake Chute Chain Caver 60033 22181 Clutch Scissor Arm (Right)
  • Page 10 LUBRICATION LUBRICATE THE PARTS PERIODICALLY AS ILLUSTRATED IN FIGURES 11,12 and 13. LUBRICATION POINTS: The following points are to be lubricated every five hours of operation with S.A.E., 20 weight I ight duty oil, unless otherwise noted. Clutch Lock-out Assembly Reverse.
  • Page 11 accessible. Tighten the adjustment nut ta tighten the chain. CAUTION: Chain should nat be tightened taa tightly. CABLE ADJUSTMENT: See Figure 13. Remove cable roller cover. Loosen the locking bolt on top of the cable roller bracket and tighten the adjustment bolt on the side. CAUTION: The cable should not be adjusted too tightly, but should allow the spout to rotate freely.
  • Page 12 .FORWARD BELT IDLER ADJUSTMENT: With the master clutch control in the forward position the edge of the reverse orm should be 01 igned with line "B". As the belts become stretched or in the installation of the new belt it may be necessary to readjust the forward belt idler in its adjustment slot to bring the reverse arm to line "B", in the forward...
  • Page 13 CHUTE REPLACEMENT CABLE REPAIR FOR MODEL 228 AND 265-2 NOTE: The reference numbers referred to in the following instructions may be found in the parts list and the exploded view. REMOVE THE BLOWER HOUSING FROM THE SNOW REMOVE THE WORN CABLE. BLOWER.
  • Page 14 265-2 MO DEL With the cable crossed wrap each end of the coble oround the upper spout in the direction as shown in Figure B. Start the cable through the holes in the chute collar from the inside and sl ip the collar aver the cable track as shown in Figure B.

This manual is also suitable for:

1265