Table of Contents
Advertisement
BEFORE STARTING ENGINE
OIL
Your lawn mower is shipped without oil in the
engine.
• Be sure mower is level and area around oil
till is clean.
• Remove engine oil cap and fill to the full
line on the dipstick.
NOTE:
Allow oil to settle down into
engine for accurate dipstick reading.
• Engine holds 20 ozs. of oil. Fortype and
grade of oil to use, see "ENGINE" in
Maintenance section of this manual.
• Pour oil slowly. Do not over till.
• Check oil level before each use. Add oil if
needed. Fill to full line on dipstick.
• To read proper level, tighten engine oil cap
each time.
• Reinstall engine oil cap and tighten.
• Change the oil after every 25 hours of
operation or each season. You may need
to change the oil more often under dusty,
dirty conditions.
ADD GASOLINE
• Fill fuel tank.
Use fresh, clean, regular
unleaded gasoline
with a minimum of
87 octane.
(Use of leaded gasoline
will increase carbon and lead oxide
deposits and reduce valve life).
Do not
mix oil with gasoline.
Purchase
fuel in
quantities
that can be used within 30
days to assure fuel freshness.
_cWhAoRNING." Experience indicates that
I blenaed fuels tcallea gasonol or
using ethanol or methanol) can attract
moisture which leads to separation and
formation
of acids during storage.
Acidic
gas can damage the fuel system of an
engine while in storage.
To avoid engine
problems, the fuel system should be
emptied before storage of 30 days or
longer. Drain the gas tank, start the
engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season.
See Storage Instructions for
additional information.
Never use engine
or carburetor cleaner products in the fuel
tank or permanent damage may occur.
,.,_.CAUTION:
Fill to bosom of gas,tank
filler neck. Do not oveniil. Wipe on any
spilled oil or fuel.
Do not store, spill or use
gasoline near an open flame.
TO START ENGINE
• To start a cold engine, push primer five
(5) times before trying to start. Use a
firm push. This step is not usually
necessary when starting an engine
which has already run for a few
minutes.
• Hold operator presence control bar
down to the handle and pull starter
handle quickly.
Do not allow starter
rope to snap back.
• To stop engine, release operator
presence control bar.
NOTE:
In cooler weather it may be
necessary to repeat priming steps. In
warmer weather over priming may cause
flooding and engine will not start. If you
do flood engine, wait a few minutes
before attempting to start and do not
repeat priming steps.
Engine oil cap
Gasoline filler
cap
MOWING TIPS
• Under certain conditions,
such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine and leaving clumps of grass
clippings. It may also be necessary to
reduce ground speed
and/or run the
lawn mower over the area a second
time.
• For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
• For better grass bagging and most
cutting conditions, the engine speed
should be set in the fast position.
• For side discharge lawn mowers,
cutting in a counter-clockwise
direction,
starting at the outside of the area to be
cut, spreads grass clippings more
evenly and puts less load on the
engine. To keep clippings off of
walkways, flower beds, etc., make the
first cuts in a clockwise direction.
• Pores in cloth grass catchers can
become filled with dirt and dust with
use and catchers will collect less grass.
To prevent this, regularly hose catcher
off with water and let dry before using.
• Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and
7
extend engine life.
Advertisement
Table of Contents
