LG RU-42PX10 Owner's Manual page 37

18. Bass (Command2:s)
I_ To adjust bass.
You can also adjust bass in the Sound menu.
Transmission
[[k][s][ ][Set ID][ ][Data][Cr] J
Data Min: 0 ~ Max: 64
• Refer to 'Real data mapping 1 '. See page 35.
Acknowledaement
[[s][ ][Set ID][ ][OK][Data][x] J
19. Balance (Command2:t)
I_ To adjust balance.
You can also adjust balance in the Sound menu.
Transmission
[[k][t][ ][Set ID][ ][Data][Cr] ]
Data Min: 0 ~ Max: 64
• Refer to 'Real data mapping 1 '. See page 35.
Acknowledqement
[[t][ ][Set ID][ ][OK][Data][x] ]
20. Color Temperature (Command2:u)
I_ To adjust color temperature,
You can also adjust ACC in the Picture menu.
Transmission
[[k][u][ ][Set ID][ ][Data][Cr] ]
Data 0: Cool 1: Normal 2: Warm 3: Off
Acknowledqement
[[u][ ][Set ID][ ][OK][Data][x] ]
21. Red
Adjustment (Command2:v)
I_ To adjust red in color temperature.
Transmission
[[k][v][ ][Set ID][ ][Data][Cr] J
Data Min: 0 - Max: 3C
• Refer to 'Real data mapping 3' as shown right.
Acknowledqement
[[v][ ][Set ID][ ][OK][Data][x] J
22. Green
Adjustment (Command2:w)
I_ To adjust green in color temperature.
Transmission
[[k][w][ ][Set ID][ ][Data][Cr] ]
Data Min: 0 ~ Max: 3C
• Refer to 'Real data mapping 3' as shown right.
Acknowledqement
[[w][ ][Set ID][ ][OK][Data][x] J
External Control Device Setup
23. Blue Adjustment (Command2:$)
I_ To adjust blue in color temperature.
Transmission
[[k][$][ ][Set ID][ ][Data][Cr] J
Data Min: 0 - Max: 3C
• Refer to 'Real data mapping 3' as shown below,
Acknowledqement
[[$][ ][Set ID][ ][OK][Data][×] ]
* Real data mapping 3
0 :-30
1 :-29
2 :-28
1E:0
i
3A : +28
3B : +29
3C : +30
24. PIP Input Select (Command2:y)
I_ To select input source for sub picture in PiP mode.
Transmission
L[k][y][ ][Set ID][ ][Data][Cr] ]
Data 0 :TV 4 :Component2
1 :Video 1 5 : RGB
2 :Video2 6 : DVl
3 : Component 1
Acknowledaement
L[y][ ][Set ID][ ][OK][Data][x] ]
25. Abnormal State
(Command2:z)
I_ To recognize an abnormal state,
Transmission
[[k][z][ ][Set ID][ ][FF][Cr] J
Data FF:Read
Acknowledqement
L[z][ ][Set Ig][ ][OK][gata][x] ]
Data 0: Normal (Power on and signal exist)
1 : No signal (Power on).
2: Turn the monitor off with remote control.
3: Turn the monitor off with Sleep Time function,
4: Turn the monitor off with RS-232C function,
5: 5V down.
6: AC down.
7: Turn the monitor off with Fan Alarm function,
8: Turn the monitor off with Off Time function.
9: Turn the monitor off with Auto Off function.
a: Turn the monitor off with On Time function.
(If you do not press any button within 2 hours after
the TV turns on with the On Timer function, the TV will
automatically revert to standby mode.)
Owner's Manual 37