Subscribe to Our Youtube Channel
Related Manuals for Yaohua Weighing System XK3190-H2B
Summary of Contents for Yaohua Weighing System XK3190-H2B
-
Page 1: User Guide
Electronic Crane Scale XK3190-H2B Weighing Indicator USER GUIDE VER 1.02 Shanghai Yaohua Weighing System Co.,Ltd. Version: May,2004... -
Page 2: Table Of Contents
Technical Specification II Configuration, Installation and Application I .Configuration of the scale body II. External layout of indicator III. Wireless working mode IV. Wire working style V. Replacing the printing paper and the ink ribbon of the micro printer VI. External printer installation VII. -
Page 3: Technical Specification
Transmitted data format Transmission Distance 8. Printer Port 9. Data Storage Technical Specification XK3190-H2B Meets the regulations of OIML, R76, JJG-555 and national standard of the electronic crane scale. Accuracy - Class Ⅲ From 0.01 to 50, 12 options in total. Verifying division will be set automatically each time when powered on. - Page 4 10. Power Supply Power of Indicator Power of Scale Body 11. Signal Transmission Transmission Distance Wireless Frequencies 12. Display Display Cycle LoBAT COMM shift 13. Other Functions 1). Various digital filtering modes are adopted. Displaying stabilizing time: ≤10s during swaying angle≤±2°...
-
Page 5: Configuration, Installation And Application
(Figure 3)Rear Wiring Layout 3. Wireless working mode: Usually, XK3190-H2B Indicator is used in wireless transmitting electronic crane scale. Install the transmitting antenna before operation, and then open the small cover on the scale body to install the battery, after inserting battery plug into the battery socket and turning on the switch, the 330 x 230 x 60 (mm) around 1.5kg... -
Page 6: Wire Working Style
The crane scale will go into the power-saving mode and twinkle once every 5 seconds when it has been out of operation or the weight on the scale has kept unchanged for 30 seconds. At this time, the scale will go into the normal working condition automatically if the load varies≥0.1%F.S and 0.3%F.S. -
Page 7: Communication Interfaces
If necessary to connect wide-format printer, please switch off power first and fix the printer cable, and then turn on the printer power to make printer online, the XK3190-H2B indicator will be get online together with printer automatically after switching on, and stop built-in micro printer operation. - Page 8 accurately. If connected in wrong way, the output port of the indicator or the input port of computer communication will be damaged, and sometimes the damage will happen to the indicator, computer and peripherals. ▲! Special computer operation skills and programming ability is required for computer communication operation, which shall be performed and directed by qualified service personnel only.
- Page 9 02H(XON) A～Z A～B Transmitting the corresponding data according to the instruction … Transmitting the corresponding data according to the instruction Transmitting the corresponding data according to the instruction Transmitting the corresponding data according to the instruction XOR verifying XOR verifying 03H (X0FF) XOR=2 ⊕...
-
Page 10: Scoreboard Connection
End sign 44 bytes in total Transmitting the accumulated weight by using the format below: Sect Length (byte) Beginning sign Transmitting head Sign Weight Unit Enter key Verifying sum End sign 24 bytes in total 3. Indicator communicating parameter setting: 1). -
Page 11: Charge
Charge the battery of scale body in time if the LoBAT character in the screen of the indicator keeps lights, which shows the battery of the body is low. Or the scale body will power off 10 minutes later. Before charging the battery in the condition of no LoBAT twinkles, press discharging button to get battery discharge, and in this way, battery capacity degradation can be effectively prevented. -
Page 12: Iii Keypad Functions
Keys setting and keypad layout The lower name on the key is the basic function and the function of the upper name on the key can be executed simultaneously by pressing <shift> key. COMM MODE TYPE TRANS ACCUM MEMO MEMO RECALL CLEAR SHIFT... - Page 13 15. <<Minus WT>> Go to minus weighing mode, the instrument identifying mark becomes F and weight displayed become 0 at the same time. The weight of the object taken off from the scale will be displayed then. Press<<Minus Weight>> to quit the minus weighing mode.
- Page 14 Weight A/D internal code Display the weight in zero point Display zero point upon powered on Calibrate zero point internal code Full Scale Check division 0.01～50, 12 options in total Displaying ratio Displaying Non-linearity edited value within the scope of –1%Max～1%Max, weight unit Initial zeroing range 2～100 unit: %Max.
- Page 15 2) Press <<Shift>><<Calibrate>>to enter into calibration procedures, “PAS” remind you of entering password. Enter 3190 and then press <<Calibrate>>. 3) “F XXXXX” reminds you of entering the Full Scale. XXXXX means the previous Full Scale. Press <<Figure>> to enter the Full Scale and then press <<Calibrate>>...
-
Page 16: Ⅳ Data Printing Format
(Initializing) zeroing scopes (P16 or P30) can be achieved by using above-mentioned method only, with 2-100(%Max) as valid value scope. Non-linearity tolerance is the difference between zero point and 50%F.S after the full scale is calibrated. Non-linearity edited value (15) is the negative of non-linearity tolerance. -
Page 17: External Printer Printing Format
Error accumulated value, the value of this type has been deleted Err 27 The figure displayed on scoreboard exceeds 6 digits (including decimal), the problem Weight list Indicator model No. : XK3190-H2B 1.02 weighing time Jan. 2004 “N” represents net weight... -
Page 18: Error Message From Wrong Inner Operation
Err 30 After the datum is stabilized for 30 minutes, the scale body powered off automatically Err 32 No signal from scale body received, cause by no battery installed or long distance. Err 33 Accumulation serial No. -
Page 19: Trouble Shooting
2. No antenna installed during 3. No Instrument 1. The weight of the goods alarm, weight value displayed 2. The battery voltage of scale printed Ink ribbon is used up figure is too vague figure The ink ribbon is out of slot... - Page 20 Notes: The specification, model and codes must be clearly expressed while purchasing optional parts. Epson ERC-05 Width 44.5±0.5mm Epson M150-II To be purchased according to wireless transmitting frequency For XK3190-H2B For XK3190-H2B For Epson M150-II For Epson M150-II 450MHz, 230MHz...
Need help?
Do you have a question about the XK3190-H2B and is the answer not in the manual?
Questions and answers